PEI ULTEM™ 1000 GY SABIC INNOVATIVE US
257
- Properties:Glass fiber reinforcedFlame retardantenhance
- Usages:Electrical fieldElectronic fieldAutomotive sector
- Certificates:UL
Compare
View PricesTechnical Data Sheet
| Physical Properties | Test Condition | Test Method | Test Result | Unit |
|---|---|---|---|---|
| Moisture Absorption | 饱和, 23°C | ISO 62 | 1.3 | % |
| 平衡, 23°C, 50% RH | ISO 62 | 0.70 | % | |
| Melt Volume flow Rate | 360°C/5.0 kg | ISO 1133 | 13.0 | cm3/10min |
| Modeling Shrinkage - Flow | 内部方法 | 0.50 到 0.70 | % |
| Mechanical Properties | Test Condition | Test Method | Test Result | Unit |
|---|---|---|---|---|
| Flexural Stress | ISO 178 | 160 | Mpa | |
| Taber Abrasion Resistance | 1000 Cycles, 1000 g, CS-17 转轮 | 内部方法 | 10.0 | mg |
| Flexural Modulus | ISO 178 | 3300 | Mpa | |
| Tensile Stress | 屈服 | ISO 527-2/50 | 105 | Mpa |
| 断裂 | ISO 527-2/50 | 85.0 | Mpa | |
| Tensile Strain | 屈服 | ISO 527-2/50 | 6.0 | % |
| 断裂 | ISO 527-2/50 | 60 | % | |
| Tensile Modulus | ISO 527-2/1 | 3200 | Mpa |
| Thermal Properties | Test Condition | Test Method | Test Result | Unit |
|---|---|---|---|---|
| Vicat Softening Temperature | -- | ISO 306/A50 | 215 | °C |
| -- | ISO 306/B50 | 211 | °C | |
| -- | ISO 306/B120 | 212 | °C | |
| Linear thermal expansion coefficient | 流动 : 23 到 150°C | ISO 11359-2 | 5.0E-5 | cm/cm/°C |
| 横向 : 23 到 150°C | ISO 11359-2 | 5.0E-5 | cm/cm/°C | |
| Ball PressureTest | 123 到 127°C | IEC 60695-10-2 | 通过 | |
| Thermal Conductivity | ISO 8302 | 0.24 | W/m/K | |
| RTI | UL 746 | 170 | °C | |
| RTI Imp | UL 746 | 170 | °C | |
| RTI Elec | UL 746 | 170 | °C | |
| Heat Deflection Temperature | 0.45 MPa, 未退火, 4.00 mm, 100 mm 跨距 | ISO 75-2/Be | 200 | °C |
| 1.8 MPa, 未退火, 4.00 mm, 100 mm 跨距 | ISO 75-2/Ae | 190 | °C |
| Electrical performance | Test Condition | Test Method | Test Result | Unit |
|---|---|---|---|---|
| Relative Permittivity | 50 Hz | IEC 60250 | 2.90 | |
| 60 Hz | IEC 60250 | 2.90 | ||
| 1 MHz | IEC 60250 | 2.90 | ||
| Comparative Tracking Index | -- | IEC 60112 | 150 | V |
| 解决方案 B | IEC 60112 | 100 | V | |
| Dielectric Strength | 0.800 mm, 在油中 | IEC 60243-1 | 33 | KV/mm |
| 1.60 mm, 在油中 | IEC 60243-1 | 25 | KV/mm | |
| 3.20 mm, 在油中 | IEC 60243-1 | 16 | KV/mm | |
| Surface Resistivity | IEC 60093 | > 1.0E+15 | ohms | |
| Volume Resistivity | IEC 60093 | 1.0E+15 | ohms·cm | |
| Dissipation Factor? | 50 Hz | IEC 60250 | 5.0E-4 | |
| 60 Hz | IEC 60250 | 5.0E-4 | ||
| 1 MHz | IEC 60250 | 6.0E-3 | ||
| 2.45 GHz | IEC 60250 | 2.5E-3 |
| Injection | Test Condition | Test Method | Test Result | Unit |
|---|---|---|---|---|
| Drying Temperature | 150 | °C | ||
| Suggested Max Moisture | 0.020 | % | ||
| Processing (Melt) Temp | 370 到 410 | °C | ||
| Mold Temperature | 140 到 180 | °C | ||
| Drying Time | 4.0 到 6.0 | hr | ||
| Rear Temperature | 340 到 395 | °C | ||
| Middle Temperature | 350 到 405 | °C | ||
| Front Temperature | 360 到 415 | °C | ||
| Nozzle Temperature | 350 到 405 | °C | ||
| Hopper Temperature | 80 到 120 | °C |
| Impact Properties | Test Condition | Test Method | Test Result | Unit |
|---|---|---|---|---|
| Notched Izod Impact Strength | -30°C | ISO 180/1A | 6.0 | kJ/m² |
| 23°C | ISO 180/1A | 6.0 | kJ/m² | |
| Unnotched Izod Impact Strength | -30°C | ISO 180/1U | 无断裂 | |
| 23°C | ISO 180/1U | 无断裂 |
| hardness | Test Condition | Test Method | Test Result | Unit |
|---|---|---|---|---|
| Ball Indentation Hardness | H 358/30 | ISO 2039-1 | 140 | Mpa |
| Flammability | Test Condition | Test Method | Test Result | Unit |
|---|---|---|---|---|
| Glow Wire Flammability Index | 3.2 mm | IEC 60695-2-12 | 960 | °C |
| Oxygen Index | ISO 4589-2 | 47 | % | |
| Flame Rating | 0.40 mm | UL 94 | V-2 | |
| 0.75 mm | UL 94 | V-0 | ||
| 3.0 mm | UL 94 | 5VA |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
