Technical Data Sheet
| Physical Properties | Test Condition | Test Method | Test Result | Unit |
|---|
| Density | | ASTM D792/ISO 1183 | 1.06 | |
| Modeling Shrinkage | | ASTM D955 | 1.3~1.4 | % |
| Moisture Absorption 23℃/24H | | ASTM D570/ISO 62 | 1.3 | % |
| Physical Properties | Test Condition | Test Method | Test Result | Unit |
|---|
| MediumDensity | | | 0.900 | g/cm³ |
| SpecificHeatCapacityofMelt | | | 2800 | J/kg/°C |
| ThermalConductivityofMelt | | | 0.19 | W/m/K |
| Modeling Shrinkage | MD：3.20mm | | 1.1 | % |
| Modeling Shrinkage | TD：3.20mm | | 1.1 | % |
| Modeling Shrinkage | TD | ISO294-4 | 1.5 | % |
| Modeling Shrinkage | MD | ISO294-4 | 1.5 | % |
| Moisture Absorption | 饱和,23°C,2.00mm | ISO62 | 3.0 | % |
| Moisture Absorption | 平衡,23°C,2.00mm,50%RH | ISO62 | 1.3 | % |
| Viscosity number | 96%H2SO4 | ISO307 | 120 | cm³/g |
| Mechanical Properties | Test Condition | Test Method | Test Result | Unit |
|---|
| Tensile Stress | 屈服 | ISO527-2 | 62.0 | Mpa |
| Tensile Strain | 屈服 | ISO527-2 | 4.3 | % |
| Tensile Elongation?(Break) | | ASTM D412/ISO 527 | 35 | % |
| Tensile Modulus | | ASTM D412/ISO 527 | 2050 | kg/cm²(MPa)[Lb/in²] |
| Tensile Modulus | | ISO527-2 | 2400 | Mpa |
| Tensile Strength | | ASTM D412/ISO 527 | 62 | kg/cm²(MPa)[Lb/in²] |
| Nominal Tensile Strain at Break | | ISO527-2 | 35 | % |
| Charpy impact strength | | ASTM D256/ISO 179 | 4 | kg·cm/cm(J/M)ft·lb/in |
| Charpy impact strength | | ASTM D256/ISO 179 | NB | kg·cm/cm(J/M)ft·lb/in |
| Charpy impact strength | | ASTM D256/ISO 179 | 5 | kg·cm/cm(J/M)ft·lb/in |
| Thermal Properties | Test Condition | Test Method | Test Result | Unit |
|---|
| Linear thermal expansion coefficient | MD | ISO11359-2 | 1.2E-04 | cm/cm/°C |
| Linear thermal expansion coefficient | TD | ISO11359-2 | 1.2E-04 | cm/cm/°C |
| Glass Transition Temperature | | ISO11357-2 | 60.0 | °C |
| Vicat Softening Temperature | | ISO306/B50 | 180 | °C |
| Melting Temperature | | ISO11357-3 | 218 | °C |
| Burning Rate | | UL94 | HB | |
| Deflection Temperature Under Load? | | ASTM D648/ISO 75 | 135 | ℃（℉） |
| Deflection Temperature Under Load? | | ASTM D648/ISO 75 | 62 | ℃（℉） |
| Deflection Temperature Under Load? | 0.45MPa,未退火 | ISO75-2/B | 135 | °C |
| Deflection Temperature Under Load? | 1.8MPa,未退火 | ISO75-2/A | 62.0 | °C |
| Melting Temperature | | | 218 | ℃（℉） |
| Linear expansion coefficient | | ASTM D696/ISO 11359 | 0.9~1.8 | |
| Electrical performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Relative Permittivity | 100Hz | IEC60250 | 3.60 | |
| Relative Permittivity | 1MHz | IEC60250 | 3.20 | |
| Dielectric Strength | | IEC60243-1 | 36 | KV/mm |
| Dissipation Factor? | 100Hz | IEC60250 | 0.014 | |
| Dissipation Factor? | 1MHz | IEC60250 | 0.017 | |
| Volume Resistivity | | IEC60093 | >1.0E+15 | ohms·cm |
| Film | Test Condition | Test Method | Test Result | Unit |
|---|
| Tensile Strain (MD) | Yield | ISO527-3 | 4.3 | % |
| Impact Properties | Test Condition | Test Method | Test Result | Unit |
|---|
| Charpy Unnotched Impact Strength | -30°C | ISO179/1eU | NoBreak | |
| Charpy Unnotched Impact Strength | 23°C | ISO179/1eU | NoBreak | |
| hardness | Test Condition | Test Method | Test Result | Unit |
|---|
| Rockwell Hardness | R级 | ISO2039-2 | 114 | |
| Flammability | Test Condition | Test Method | Test Result | Unit |
|---|
| UL flame retardant rating | 0.9mm | IEC60695-11-10,-20 | HB | |
| UL flame retardant rating | 1.5mm | IEC60695-11-10,-20 | HB | |
| UL flame retardant rating | 0.9mm | UL94 | HB | |
| UL flame retardant rating | 1.5mm | UL94 | HB | |
| Oxygen Index | | ISO4589-2 | 25 | % |
| FMVSS Flammability | | FMVSS302 | B | |
| Burning Rate | 1.00mm | ISO3795 | <100 | mm/min |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare
View Prices