Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result | Unit |
|---|
| Apparent density | | ISO 60 | 0.8 | g/cm³ |
| Melt volume flow rate | 260℃，5 kg 260℃/5.0 kg | ISO 1133 | 15 | cm3/10min |
| Shrinkage rate | TD：250℃，2.0 mm Across Flow : 482°F, 0.0787 in 2 2 | ISO 294-4 | 0.9 | % |
| Shrinkage rate | TD：120℃，2.0 mm，2 hrs Across Flow : 120°C, 2 hr, 2.00 mm 3 3 | ISO 294-4 | 0.5 | % |
| Shrinkage rate | MD：250℃，2.0 mm Flow : 482°F, 0.0787 in 2 2 | ISO 294-4 | 0.9 | % |
| Shrinkage rate | MD：120℃，2.0 mm，2 hrs Flow : 120°C, 2 hr, 2.00 mm 3 3 | ISO 294-4 | 0.5 | % |
| Mechanical performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Tensile modulus | 23℃ 23℃ | ISO 527-1-2 | 2400 | Mpa |
| Tensile strength | 屈服，23℃ 屈服，23℃ | ISO 527-2/50 | 45 | Mpa |
| Tensile strain | 屈服，23℃ 屈服，23℃ | ISO 527-2/50 | 2.9 | % |
| Nominal tensile fracture strain | 23℃ 23℃ | ISO 527-2/50 | > 15 | % |
| Bending modulus | 23℃ 23℃ 4 | ISO 178-A | 2500 | Mpa |
| bending strength | 3.50% 应变 3.5% Strain | ISO 178-A | 70 | Mpa |
| bending strength | 23℃ 23°C | ISO 178 | 75 | Mpa |
| Bending strain | | | 5 | % |
| Ball pressure hardness | | ISO 2039-1 | 104 | Mpa |
| Electrical performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Relative permittivity | 23℃，100 Hz 23°C, 100 Hz | IEC 60250 | 3.3 | |
| Relative permittivity | 23℃，1 MHz 23°C, 1 MHz | IEC 60250 | 2.9 | |
| Dissipation factor | 23℃，100 Hz 23°C, 100 Hz | IEC 60250 | 0.025 | |
| Dissipation factor | 23℃，1 MHz 23°C, 1 MHz | IEC 60250 | 0.014 | |
| Compared to the leakage trace index | 解决方案 A 解决方案 A | IEC 60112 | 300 | V |
| Impact performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Impact strength of simply supported beam without notch | -30℃ -30°C | ISO 179/1eU | 170 | kJ/m² |
| Impact strength of simply supported beam without notch | 23℃ 23°C | ISO 179/1eU | No Break | |
| Impact strength of cantilever beam gap | -30℃ -30°C | ISO 180-1A | < 10 | kJ/m² |
| Impact strength of cantilever beam gap | 0℃ 0°C | ISO 180-1A | 11 | kJ/m² |
| Impact strength of cantilever beam gap | 23℃ 23°C | ISO 180-1A | 10 | kJ/m² |
| Cantilever beam without notch impact strength | -30℃ -30°C | ISO 180/1U | 150 | kJ/m² |
| Cantilever beam without notch impact strength | 23℃ 23°C | ISO 180/1U | No Break | |
| Flame retardant performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Flame retardant grade 0.75 mm | 0.75 mm | UL 94 | V-0 | |
| Flammability index of heating wire | 0.80 mm 0.8 mm | IEC 60695-2-12 | 960 | °C |
| Ignition temperature of heating wire | 0.8 mm 0.8 mm | IEC 60695-2-13 | 800 | °C |
| Ignition temperature of heating wire | 1.6 mm 1.6 mm | IEC 60695-2-13 | 800 | °C |
| Ignition temperature of heating wire | 3 mm 3.0 mm | IEC 60695-2-13 | 800 | °C |
| Thermal performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Hot deformation temperature | 1.8 MPa，未退火 1.8 MPa，未退火 | ISO 75-2/A | 75 | °C |
| Hot deformation temperature | 0.45 MPa，未退火 0.45 MPa，未退火 | ISO 75-2/B | 95 | °C |
| Vicat softening temperature | B120 B120 | ISO 306/B120 | 118 | °C |
| Ball pressure test | 115℃ 115℃ | IEC 60695-10-2 | Pass | |
| Melting temperature | | ISO 11357-3 | 225 | °C |
| Linear coefficient of thermal expansion | TD：23~55℃ TD：23 到 55℃ | ISO 11359-2 | 0.00010 | 1/℃ |
| Linear coefficient of thermal expansion | MD：23~55℃ MD：23 到 55℃ | ISO 11359-2 | 0.000080 | 1/℃ |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare
View Prices