Technical Data Sheet
Compare
| physical property | Test Condition | Test Method | Test Result | Unit |
|---|
| Shrinkage rate | MD：3.20mm | 内部方法 | 0.50到0.70 | % |
| Water absorption rate | 24hr | ASTMD570 | 0.15 | % |
| Water absorption rate | Equilibrium,23°C | ASTMD570 | 0.35 | % |
| Water absorption rate | Equilibrium,100°C | ASTMD570 | 0.58 | % |
| Melt mass flow rate | 300°C/1.2kg | ASTMD1238 | 18 | g/10min |
| Specific volume | | ASTMD792 | 0.830 | cm³/g |
| Outdoor applicability | | UL746C | f2 | |
| Mechanical performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Tensile strength 1 | Yield | ASTMD638 | 62.1 | Mpa |
| Tensile strength 1 | Break | ASTMD638 | 65.5 | Mpa |
| Taber abraser | 1000Cycles,1000g,CS-17Wheel | ASTMD1044 | 10.0 | mg |
| Bending modulus 3 | 50.0mmSpan | ASTMD790 | 2340 | Mpa |
| Elongation rate 2 | Yield | ASTMD638 | 7.0 | % |
| Elongation rate 2 | Break | ASTMD638 | 110 | % |
| Bending strength 4 | Yield,50.0mmSpan | ASTMD790 | 93.1 | Mpa |
| Thermal performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Linear coefficient of thermal expansion | MD：-40to95°C | ASTME831 | 6.8E-05 | cm/cm/°C |
| specific heat | | ASTMC351 | 1260 | J/kg/°C |
| thermal conductivity | | ASTMC177 | 0.25 | W/m/K |
| RTI | | UL746 | 80.0 | °C |
| BallPressure Test | 125°C | IEC60695-10-2 | Pass | |
| Hot deformation temperature | 0.45MPa,Unannealed,6.40mm | ASTMD648 | 138 | °C |
| Hot deformation temperature | 1.8MPa,Unannealed,6.40mm | ASTMD648 | 132 | °C |
| RTIElec | | UL746 | 80.0 | °C |
| Evolution Calendar intelligent importer | | UL746 | 80.0 | °C |
| Vicat softening temperature | | ASTMD152512 | 154 | °C |
| Electrical performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Dissipation factor | 50Hz | ASTMD150 | 9E-04 | |
| Dissipation factor | 60Hz | ASTMD150 | 9E-04 | |
| Dissipation factor | 1MHz | ASTMD150 | 0.010 | |
| Dielectric constant | 50Hz | ASTMD150 | 3.17 | |
| Dielectric constant | 60Hz | ASTMD150 | 3.17 | |
| Dielectric constant | 1MHz | ASTMD150 | 2.96 | |
| Volume resistivity | | ASTMD257 | >1.0E+17 | ohms·cm |
| Compared to the anti leakage trace index | CTI | UL746 | PLC3 | |
| Dielectric strength | 3.20mm,inAir | ASTMD149 | 15 | KV/mm |
| Hot wire ignition | HWI | UL746 | PLC3 | |
| High arc combustion index | HAI | UL746 | PLC1 | |
| Impact performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Falling hammer impact | 23°C | ASTMD3029 | 169 | J |
| 23°C | | ASTMD4812 | 3200 | J/m |
| 23°C | | ASTMD256 | 600 | J/m |
| 23°C10 | | ISO180/1U | 无断裂 | |
| Simple supported beam without notch impact strength 6 | -30°C | ISO179/1eU | 无断裂 | |
| Simple supported beam without notch impact strength 6 | 23°C | ISO179/1eU | 无断裂 | |
| 23°C8 | | ISO180/1A | 65 | kJ/m² |
| -30°C9 | | ISO180/1U | 无断裂 | |
| Impact strength of simply supported beam gap 5 | 23°C | ISO179/1eA | 65 | kJ/m² |
| Impact strength of simply supported beam gap 5 | -30°C | ISO179/1eA | 12 | kJ/m² |
| -30°C7 | | ISO180/1A | 11 | kJ/m² |
| Tensile impact strength 11 | | ASTMD1822 | 546 | kJ/m² |
| hardness | Test Condition | Test Method | Test Result | Unit |
|---|
| Rockwell hardness | M-Scale | ASTMD785 | 70 | |
| Rockwell hardness | R-Scale | ASTMD785 | 118 | |
| flammability | Test Condition | Test Method | Test Result | Unit |
|---|
| UL flame retardant rating | 0.750to1.65mm | UL94 | V-2 | |
| Burning wire flammability index | 0.750mm | IEC60695-2-12 | 750 | °C |
| Burning wire flammability index | 1.50mm | IEC60695-2-12 | 850 | °C |
| Hot filament ignition temperature | 0.750mm13 | IEC60695-2-13 | 875 | °C |
| Hot filament ignition temperature | 1.50mm | IEC60695-2-13 | 850 | °C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
