Technical Data Sheet
| Physical Properties | Test Condition | Test Method | Test Result | Unit |
|---|
| Haze | | | 优级｜≤75 | % |
| Haze | | | 一级｜- | % |
| Haze | | | 合格｜- | % |
| Nominal Tensile Strain at Break | | IEC60093 | 652 | % |
| Mechanical Properties | Test Condition | Test Method | Test Result | Unit |
|---|
| Tensile Strength(Break) | | | 优级｜≥22 | Mpa |
| Tensile Strength(Break) | | | 一级｜≥20 | Mpa |
| Tensile Strength(Break) | | | 合格｜≥18 | Mpa |
| Instrumented Dart Impact | | | 合格｜- | g |
| Instrumented Dart Impact | | | 优级｜≤80 | g |
| Instrumented Dart Impact | | | 一级｜- | g |
| Tensile Strength | | | 30 | Mpa |
| Tensile Elongation | 断裂 | | 优级｜≥450 | % |
| Tensile Elongation | 断裂 | | 一级｜≥450 | % |
| Tensile Elongation | 断裂 | | 合格｜≥450 | % |
| Tensile Elongation | 断裂 | | 400 | % |
| Other | Test Condition | Test Method | Test Result | Unit |
|---|
| Fish Eye | 0.4mm | | 优级｜≤15 | 个/1520cm2 |
| Fish Eye | 0.4mm | | 一级｜≤25 | 个/1520cm2 |
| Fish Eye | 0.4mm | | 合格｜≤40 | 个/1520cm2 |
| Fish Eye | 0.8mm | | 优级｜≤2 | 个/1520cm2 |
| Fish Eye | 0.8mm | | 一级｜≤4 | 个/1520cm2 |
| Fish Eye | 0.8mm | | 合格｜≤8 | 个/1520cm2 |
| Particle Size | 蛇皮和丝发 | | 优级｜≤20 | 个/kg |
| Particle Size | 蛇皮和丝发 | | 一级｜≤20 | 个/kg |
| Particle Size | 蛇皮和丝发 | | 合格｜≤40 | 个/kg |
| Particle Size | 大粒和小粒 | | 优级｜≤10 | g/kg |
| Particle Size | 大粒和小粒 | | 一级｜≤10 | g/kg |
| Particle Size | 大粒和小粒 | | 合格｜≤10 | g/kg |
| Particle Size | 污染粒子 | | 优级｜≤10 | 个/kg |
| Particle Size | 污染粒子 | | 一级｜≤20 | 个/kg |
| Particle Size | 污染粒子 | | 合格｜≤40 | 个/kg |
| Physical | Test Condition | Test Method | Test Result | Unit |
|---|
| Melt Mass-Flow Rate | | | 优级｜0.4±0.02 | g/10min |
| Melt Mass-Flow Rate | | | 一级｜0.4±0.02 | g/10min |
| Melt Mass-Flow Rate | | | 合格｜0.4±0.04 | g/10min |
| Melt index | 21.6kg | | 9 | g/10min |
| Density | | | 0.948 | kg/m |
| Density | | | 优级｜0.948±0.002 | g/cm³ |
| Density | | | 一级｜0.948±0.003 | g/cm³ |
| Density | | | 合格｜0.948±0.004 | g/cm³ |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare