Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result | Unit |
|---|
| Water absorption rate | 24 hr, 23°C | ASTM D570 | 1.3 | % |
| Shrinkage rate - flow | 23°C, 3.20 mm, 注塑 | ASTM D955 | 0.90 到 1.6 | % |
| Mechanical performance | Test Condition | Test Method | Test Result | Unit |
|---|
| elongation | 断裂, 23°C, 3.20 mm, 注塑 | ASTM D638 | 28 | % |
| Bending modulus | 23°C, 6.40 mm, 注塑 | ASTM D790 | 3330 | Mpa |
| bending strength | 23°C, 6.40 mm, 注塑 | ASTM D790 | 113 | Mpa |
| Tensile strength | 屈服, 23°C, 3.20 mm, 注塑 | ASTM D638 | 78.5 | Mpa |
| Thermal performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Linear coefficient of thermal expansion - flow | | ASTM D696 | 7.0E-5 | cm/cm/°C |
| Peak melting temperature | | ASTM D3418 | 260 | °C |
| Thermal deformation temperature under load | 0.45 MPa, 未退火, 6.40 mm, 注塑 | ASTM D648 | 230 | °C |
| Thermal deformation temperature under load | 1.8 MPa, 未退火, 6.40 mm, 注塑 | ASTM D648 | 85.0 | °C |
| Electrical performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Leakage Trace Index | | IEC 60112 | 600 | V |
| Dielectric strength | 23°C, 1.00 mm | ASTM D149 | 22 | KV/mm |
| Dielectric constant | 23°C, 1 MHz | ASTM D150 | 3.00 | |
| Volume resistivity | 23°C | ASTM D257 | 1.0E+14 | ohms·cm |
| injection | Test Condition | Test Method | Test Result | Unit |
|---|
| drying temperature | | | 80 到 100 | °C |
| Suggested maximum moisture content | | | 0.10 | % |
| Processing (melt) temperature | | | 260 到 280 | °C |
| Mold temperature | | | 60 到 90 | °C |
| drying time | | | 4.0 到 5.0 | hr |
| Temperature at the rear of the barrel | | | 255 到 270 | °C |
| Temperature in the middle of the barrel | | | 260 到 275 | °C |
| Temperature at the front of the material cylinder | | | 260 到 275 | °C |
| Spray nozzle temperature | | | 270 到 280 | °C |
| Back pressure | | | 0.490 到 1.96 | Mpa |
| Screw speed | | | 60 到 200 | rpm |
| hardness | Test Condition | Test Method | Test Result | Unit |
|---|
| Rockwell hardness | R 级, 23°C, 注塑 | ASTM D785 | 120 | |
| flammability | Test Condition | Test Method | Test Result | Unit |
|---|
| UL flame retardant rating | 0.40 到 0.82 mm | UL 94 | V-0 | |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare
View Prices