Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result | Unit |
|---|
| Density/specific gravity 2 | | ASTMD792 | 1.17 | g/cm³ |
| Density/specific gravity | 23°C | ISO1183 | 1.17 | g/cm³ |
| Melt mass flow rate | 260°C/2.16kg | ASTMD1238 | 20 | g/10min |
| Melt volume flow rate | 260°C/2.16kg | ISO1133 | 21.0 | cm3/10min |
| SpiralFlow3.4 | | 内部方法 | 45.0 | CM |
| Shrinkage rate | MD | ASTMD955 | 0.40to0.60 | % |
| Shrinkage rate | | ISO2577 | 0.40to0.60 | % |
| Mechanical performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Tensile strength 5 | Yield,23°C | ASTMD638 | 49.0 | Mpa |
| Tensile stress | 屈服 | ISO527-2/50 | 55.0 | Mpa |
| Tensile stress | 断裂 | ISO527-2/50 | 45.0 | Mpa |
| Tensile strain 5 | Break,23°C | ASTMD638 | 100 | % |
| Tensile strain | 断裂 | ISO527-2/50 | 110 | % |
| Bending modulus 6 | 23°C | ASTMD790 | 245 | Mpa |
| Bending modulus 7 | | ISO178 | 2500 | Mpa |
| FlexuralStrength6 | 23°C | ASTMD790 | 78.5 | Mpa |
| Bending stress 7 | | ISO178 | 80.0 | Mpa |
| Thermal performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Linear coefficient of thermal expansion | MD：23到55°C | ISO11359-2 | 8E-05 | cm/cm/°C |
| Hot deformation temperature 9 | 1.8MPa,未退火,3.20mm | ASTMD648 | 78.0 | °C |
| Hot deformation temperature 9 | 1.8MPa,未退火,6.40mm | ASTMD648 | 87.0 | °C |
| Hot deformation temperature 9 | 1.8MPa,Unannealed,4.00mm | ISO75-2/A | 73.0 | °C |
| Vicat softening temperature | -- | ASTMD152510 | 94.0 | °C |
| Vicat softening temperature | -- | ASTMD152511 | 85.0 | °C |
| Vicat softening temperature | -- | ISO306/A50 | 94.0 | °C |
| Vicat softening temperature | -- | ISO306/B50 | 85.0 | °C |
| Electrical performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Surface resistivity | | IEC60093 | 2.9E+17 | ohms |
| Volume resistivity | | IEC60093 | 3.9E+19 | ohms·cm |
| Dielectric constant | 1MHz | IEC60250 | 3.10 | |
| Impact performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Suspended wall beam gap impact strength 8 | 23°C | ISO180 | 45 | kJ/m² |
| Impact strength of simply supported beam gap 8 | -30°C | ISO179 | 15 | kJ/m² |
| Impact strength of simply supported beam gap 8 | 23°C | ISO179 | 45 | kJ/m² |
| Impact strength of cantilever beam gap | 23°C,3.18mm | ASTMD256 | 590 | J/m |
| Suspended wall beam gap impact strength 8 | -30°C | ISO180 | 15 | kJ/m² |
| hardness | Test Condition | Test Method | Test Result | Unit |
|---|
| Rockwell hardness | R计秤,23°C | ASTMD785 | 113 | |
| Rockwell hardness | R计秤,23°C | ISO2039-2 | 113 | |
| flammability | Test Condition | Test Method | Test Result | Unit |
|---|
| UL flame retardant rating | 1.5mm | UL94 | V-0 | |
| UL flame retardant rating | 2.1mm | UL94 | 5VB | |
| UL flame retardant rating | 3.0mm | UL94 | 5VA | |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare
View Prices