PBT VALOX™ 420-1001 SABIC INNOVATIVE US
373
- Properties:Glass fiber reinforceddimensional stabilityHigh rigidityhigh strengthheat-resisting
- Usages:Lawn equipmentElectrical fieldElectrical appliancesElectronic fieldLighting fixturesEngine hood partsTextile applicationIndustrial applicationsNursing suppliesHousehold goodsArchitectural applicationAutomotive interior partsAutomotive External PartsPetroleum ApplicationsOutdoor applicationssporting goodsNatural gas suppliesMedical suppliesGarden equipmentCharger casingLighting applications
- Certificates:UL
Compare
View PricesTechnical Data Sheet
| physical property | Test Condition | Test Method | Test Result | Unit |
|---|---|---|---|---|
| Shrinkage rate | MD：--3 | 内部方法 | 0.30to0.50 | % |
| TD：--3 | 内部方法 | 0.40to0.60 | % | |
| TD：--2 | 内部方法 | 0.50to1.0 | % | |
| MD：--4 | 内部方法 | 0.50to0.80 | % | |
| MD：--2 | 内部方法 | 0.30to0.70 | % | |
| MD：3.20mm | 内部方法 | 0.30to0.80 | % | |
| TD：--5 | 内部方法 | 0.60to0.90 | % | |
| TD：3.20mm | 内部方法 | 0.50to1.0 | % | |
| Water absorption rate | 24hr | ASTMD570 | 0.090 | % |
| 平衡,23°C,50%RH | ISO62 | 0.080 | % | |
| Melt mass flow rate | 250°C/2.16kg | ISO1133 | 17 | g/10min |
| Melt volume flow rate | 250°C/2.16kg | ISO1133 | 13.0 | cm3/10min |
| Specific volume | ASTMD792 | 0.660 | cm³/g |
| Mechanical performance | Test Condition | Test Method | Test Result | Unit |
|---|---|---|---|---|
| Tensile strain 7 | Yield | ASTMD638 | 2.7 | % |
| Break | ASTMD638 | 2.7 | % | |
| Bending modulus 8 | 50.0mmSpan | ASTMD790 | 7580 | Mpa |
| Tensile strength 7 | Break | ASTMD638 | 120 | Mpa |
| Yield | ASTMD638 | 120 | Mpa | |
| Flexural Strength8 | Yield,50.0mmSpan | ASTMD790 | 195 | Mpa |
| Break,50.0mmSpan | ASTMD790 | 190 | Mpa | |
| Bending modulus 9 | ISO178 | 8500 | Mpa | |
| Taber abraser | 1000Cycles,1000g,CS-17转轮 | ASTMD1044 | 19.0 | mg |
| Tensile stress | 断裂 | ISO527-2/5 | 125 | Mpa |
| 屈服 | ISO527-2/5 | 125 | Mpa | |
| Tensile strain | 断裂 | ISO527-2/5 | 2.0 | % |
| 屈服 | ISO527-2/5 | 2.0 | % | |
| Tensile modulus | ISO527-2/1 | 9300 | Mpa | |
| Bending strength 9,10 | ISO178 | 195 | Mpa | |
| Tensile modulus 6 | ASTMD638 | 9300 | Mpa |
| Thermal performance | Test Condition | Test Method | Test Result | Unit |
|---|---|---|---|---|
| Hot deformation temperature 13 | 0.45MPa,Unannealed,64.0mmSpan | ISO75-2/Bf | 217 | °C |
| 1.8MPa,Unannealed,64.0mmSpan | ISO75-2/Af | 204 | °C | |
| Hot deformation temperature | 0.45MPa,未退火,6.40mm | ASTMD648 | 216 | °C |
| 1.8MPa,未退火,3.20mm | ASTMD648 | 203 | °C | |
| 1.8MPa,未退火,6.40mm | ASTMD648 | 207 | °C | |
| 0.45MPa,未退火,3.20mm | ASTMD648 | 220 | °C | |
| Linear coefficient of thermal expansion | MD：-40to40°C | ASTME831 | 2.5E-05 | cm/cm/°C |
| MD：60to138°C | ASTME831 | 2.5E-05 | cm/cm/°C | |
| MD：-40到40°C | ISO11359-2 | 2.5E-05 | cm/cm/°C | |
| TD：-40到40°C | ASTME831 | 1.2E-04 | cm/cm/°C | |
| TD：-40到40°C | ISO11359-2 | 1.2E-04 | cm/cm/°C | |
| RTIElec | UL746 | 140 | °C | |
| Evolution Calendar intelligent importer | UL746 | 140 | °C | |
| RTIStr | UL746 | 140 | °C | |
| Vicat softening temperature | -- | ISO306/A50 | 223 | °C |
| -- | ISO306/B50 | 215 | °C | |
| ASTMD152514 | 215 | °C | ||
| -- | ISO306/B120 | 215 | °C | |
| thermal conductivity | ISO8302 | 0.19 | W/m/K | |
| BallPressure Test | 125°C | IEC60695-10-2 | Pass |
| Electrical performance | Test Condition | Test Method | Test Result | Unit |
|---|---|---|---|---|
| Compared to the anti leakage trace index | CTI | UL746 | PLC0 | |
| Relative permittivity | 50Hz | IEC60250 | 3.10 | |
| 1MHz | IEC60250 | 3.10 | ||
| 60Hz | IEC60250 | 3.10 | ||
| Leakage Trace Index | IEC60112 | 300 | V | |
| Dissipation factor | 1MHz | ASTMD150 | 0.020 | |
| 50Hz | IEC60250 | 1E-03 | ||
| 60Hz | IEC60250 | 1E-03 | ||
| 100Hz | ASTMD150 | 2E-03 | ||
| 1MHz | IEC60250 | 0.010 | ||
| 100Hz | IEC60250 | 1E-03 | ||
| Dielectric strength | 3.20mm,在油中 | IEC60243-1 | 16 | KV/mm |
| 3.20mm,inAir | ASTMD149 | 19 | KV/mm | |
| 1.60mm,在油中 | IEC60243-1 | 24 | KV/mm | |
| 1.00mm15 | IEC60243-1 | 19 | KV/mm | |
| 1.60mm,在油中 | ASTMD149 | 25 | KV/mm | |
| 0.800mm,在油中 | IEC60243-1 | 28 | KV/mm | |
| Surface resistivity | IEC60093 | >1.0E+15 | ohms | |
| Dielectric constant | 1MHz | ASTMD150 | 3.70 | |
| 100Hz | ASTMD150 | 3.80 | ||
| Volume resistivity | IEC60093 | >1.0E+15 | ohms·cm | |
| ASTMD257 | >3.2E+16 | ohms·cm | ||
| Arc resistance 16 | ASTMD495 | PLC5 | ||
| High voltage arc tracing rate | HVTR | UL746 | PLC1 |
| Impact performance | Test Condition | Test Method | Test Result | Unit |
|---|---|---|---|---|
| Dart impact equipped with measuring instruments | 23°C,TotalEnergy | ASTMD3763 | 8.00 | J |
| Simply supported beam without notch impact strength 11 | -30°C | ISO179/1eU | 45 | kJ/m² |
| 23°C | ISO179/1eU | 45 | kJ/m² | |
| Impact strength of simply supported beam gap 11 | 23°C | ISO179/1eA | 5.0 | kJ/m² |
| -30°C | ISO179/1eA | 5.0 | kJ/m² | |
| Unscented Izod Impact Strength 12 | -30°C | ISO180/1U | 45 | kJ/m² |
| 23°C | ISO180/1U | 45 | kJ/m² | |
| Suspended wall beam gap impact strength 12 | 23°C | ISO180/1A | 8.0 | kJ/m² |
| -30°C | ISO180/1A | 7.0 | kJ/m² |
| hardness | Test Condition | Test Method | Test Result | Unit |
|---|---|---|---|---|
| Rockwell hardness | R级 | ISO2039-2 | 118 | |
| R级 | ASTMD785 | 118 | ||
| Ball pressure hardness | H358/30 | ISO2039-1 | 122 | Mpa |
| flammability | Test Condition | Test Method | Test Result | Unit |
|---|---|---|---|---|
| UL flame retardant rating | 0.8mm | UL94 | HB | |
| Burning wire flammability index | 1.0mm | IEC60695-2-12 | 750 | °C |
| Extreme Oxygen Index | ASTMD2863 | 19 | % |
| Supplementary Information | Test Condition | Test Method | Test Result | Unit |
|---|---|---|---|---|
| Filling material | ASTMD229 | 30 | % |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
