Technical Data Sheet
| physical property | Test Condition | Test Method | Test Result | Unit |
|---|
| Density/specific gravity | 23°C | ISO1183 | 1.20 | g/cm³ |
| Apparent density | | ISO60 | 0.70 | g/cm³ |
| Melt volume flow rate | 260°C/5.0kg | ISO1133 | 16.0 | cm3/10min |
| Water absorption rate | 饱和,23°C | ISO62 | 0.50 | % |
| Water absorption rate | 平衡,23°C,50%RH | ISO62 | 0.20 | % |
| Mechanical performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Tensile modulus | 23°C | ISO527-2/1 | 2150 | Mpa |
| Tensile stress | 屈服,23°C | ISO527-2/50 | 50.0 | Mpa |
| Tensile stress | 断裂,23°C | ISO527-2/50 | 45.0 | Mpa |
| Tensile strain | 屈服,23°C | ISO527-2/50 | 4.0 | % |
| Nominal tensile fracture strain | 23°C | ISO527-2/50 | >50 | % |
| Bending modulus 2 | 23°C | ISO178 | 2100 | Mpa |
| Bending stress 2 | 23°C | ISO178 | 75.0 | Mpa |
| Bending stress 2 | 3.5%Strain,23°C | ISO178 | 66.0 | Mpa |
| Bending strain 3 | 23°C | ISO178 | 5.5 | % |
| Thermal performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Hot deformation temperature | 0.45MPa,未退火 | ISO75-2/B | 106 | °C |
| Hot deformation temperature | 1.8MPa,未退火 | ISO75-2/A | 82.0 | °C |
| Vicat softening temperature | | ISO306/B120 | 125 | °C |
| Melting temperature 5 | | ISO11357-3 | 223 | °C |
| Linear coefficient of thermal expansion | MD：23到55°C | ISO11359-2 | 9E-05 | cm/cm/°C |
| Linear coefficient of thermal expansion | TD：23to55°C | ISO11359-2 | 9E-05 | cm/cm/°C |
| ThermalConductivity5 | 23°C | ISO8302 | 0.20 | W/m/K |
| Electrical performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Surface resistivity | | IEC60093 | >1.0E+17 | ohms |
| Volume resistivity | 23°C | IEC60093 | >1.0E+17 | ohms·cm |
| Dielectric strength | 23°C,1.00mm | IEC60243-1 | 35 | KV/mm |
| Relative permittivity | 23°C,100Hz | IEC60250 | 3.20 | |
| Relative permittivity | 23°C,1MHz | IEC60250 | 3.10 | |
| Dissipation factor | 23°C,100Hz | IEC60250 | 1.5E-03 | |
| Dissipation factor | 23°C,1MHz | IEC60250 | 0.013 | |
| Leakage Trace Index | 解决方案A | IEC60112 | 500 | V |
| Leakage Trace Index | 解决方案B | IEC60112 | 100 | V |
| Impact performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Charpy Notched Impact Strength | -30°C | ISO179/1eA | 45 | kJ/m² |
| Charpy Notched Impact Strength | 23°C | ISO179/1eA | 60 | kJ/m² |
| Impact strength of simply supported beam without notch | -30°C | ISO179/1eU | NoBreak | |
| Impact strength of simply supported beam without notch | 23°C | ISO179/1eU | NoBreak | |
| Impact strength of cantilever beam gap | -30°C | ISO180/A | 45 | kJ/m² |
| Impact strength of cantilever beam gap | -20°C | ISO180/A | 52 | kJ/m² |
| Impact strength of cantilever beam gap | 23°C | ISO180/A | 60 | kJ/m² |
| Unscented Izod impact strength | -30°C | ISO180 | NoBreak | |
| Unscented Izod impact strength | 23°C | ISO180 | NoBreak | |
| hardness | Test Condition | Test Method | Test Result | Unit |
|---|
| Ball pressure hardness | | ISO2039-1 | 100 | Mpa |
| flammability | Test Condition | Test Method | Test Result | Unit |
|---|
| FlameRating | 1.6mm | UL94 | HB | |
| Burning wire flammability index | 2.0mm | IEC60695-2-12 | 700 | °C |
| Extreme Oxygen Index 6 | | ISO4589-2 | 21 | % |
| Burning rate - US-FMVSS | >1.00mm | ISO3795 | passed | |
| Supplementary Information | Test Condition | Test Method | Test Result | Unit |
|---|
| ElectrolyticalCorrosion | 23°C | IEC60426 | A1 | |
| GottfertMeltViscosity7 | 260°C | 内部方法 | 670 | Pa·s |
| ISO Shortcut | | | ISO7792-1-PBT/PC,MHPR,-020 | |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
Compare
View Prices