Technical Data Sheet
Physical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Modeling Shrinkage | MD1 | 内部方法 | 0.50到0.70 | % |
Moisture Absorption | Saturation,23°C | ISO62 | 0.35 | % |
Moisture Absorption | Equilibrium,23°C,50%RH | ISO62 | 0.15 | % |
Outdoor Suitability | | UL746C | f1 | |
Melt Volume flow Rate | 300°C/1.2kg | ISO1133 | 10.0 | cm3/10min |
Mechanical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Flexural Stress | | ISO178 | 90.0 | Mpa |
Tensile Stress | Yield | ISO527-2/50 | 63.0 | Mpa |
Tensile Stress | Break | ISO527-2/50 | 65.0 | Mpa |
Tensile Strain | Yield | ISO527-2/50 | 6.0 | % |
Tensile Strain | Break | ISO527-2/50 | 100 | % |
Tensile Modulus | | ISO527-2/1 | 2350 | Mpa |
Flexural Modulus | | ISO178 | 2300 | Mpa |
Thermal Properties | Test Condition | Test Method | Test Result | Unit |
---|
RTIElec | | UL746 | 130 | °C |
Evolution Calendar intelligent importer | | UL746 | 120 | °C |
-- | | ISO306/B50 | 141 | °C |
-- | | ISO306/B120 | 142 | °C |
RTI | | UL746 | 125 | °C |
Ball PressureTest | 125°C | IEC60695-10-2 | Pass | |
Thermal Conductivity | | ISO8302 | 0.20 | W/m/K |
Linear thermal expansion coefficient | MD:23to80°C | ISO11359-2 | 7E-05 | cm/cm/°C |
Linear thermal expansion coefficient | TD:23to80°C | ISO11359-2 | 7E-05 | cm/cm/°C |
0.45MPa, Unannealed,100mm Span | | ISO75-2/Be | 136 | °C |
1.8MPa, Unannealed,100mm Span | | ISO75-2/Ae | 125 | °C |
Electrical performance | Test Condition | Test Method | Test Result | Unit |
---|
Dissipation Factor? | 50Hz | IEC60250 | 1E-03 | |
Dissipation Factor? | 60Hz | IEC60250 | 1E-03 | |
Dissipation Factor? | 1MHz | IEC60250 | 0.010 | |
Dielectric Strength | 3.20mm,in Oil | IEC60243-1 | 17 | KV/mm |
Relative Permittivity | 50Hz | IEC60250 | 2.70 | |
Relative Permittivity | 60Hz | IEC60250 | 2.70 | |
Relative Permittivity | 1MHz | IEC60250 | 2.70 | |
Comparative Tracking Index | | IEC60112 | 225 | V |
Surface Resistivity | | IEC60093 | >1.0E+15 | ohms |
Volume Resistivity | | IEC60093 | >1.0E+15 | ohms·cm |
Impact Properties | Test Condition | Test Method | Test Result | Unit |
---|
Charpy Notched Impact Strength | -30°C | ISO179/1eA | 14 | kJ/m² |
Charpy Notched Impact Strength | 23°C | ISO179/1eA | 73 | kJ/m² |
Charpy Unnotched Impact Strength | -30°C | ISO179/1eU | 无断裂 | |
Charpy Unnotched Impact Strength | 23°C | ISO179/1eU | 无断裂 | |
Notched Izod Impact Strength | -30°C | ISO180/1A | 12 | kJ/m² |
Notched Izod Impact Strength | 23°C | ISO180/1A | 70 | kJ/m² |
Unnotched Izod Impact Strength | -30°C | ISO180/1U | 无断裂 | |
Unnotched Izod Impact Strength | 23°C | ISO180/1U | 无断裂 | |
hardness | Test Condition | Test Method | Test Result | Unit |
---|
Ball Indentation Hardness | H358/30 | ISO2039-1 | 95.0 | Mpa |
optical performance | Test Condition | Test Method | Test Result | Unit |
---|
Refractive index of light | | ISO489 | 1.586 | |
Transmittance | 2540µm | ASTMD1003 | 88.0 | % |
Flammability | Test Condition | Test Method | Test Result | Unit |
---|
UL flame retardant rating | 1.50mm | UL94 | V-2 | |
UL flame retardant rating | 3.00mm | UL94 | V-0 | |
Glow Wire Flammability Index | 1.00mm | IEC60695-2-12 | 960 | °C |
Oxygen Index | | ISO4589-2 | 35 | % |
Glow Wire Ignition Temperature | 1.00mm | IEC60695-2-13 | 850 | °C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.