Technical Data Sheet
Physical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Modeling Shrinkage | Across Flow | ISO 294-4 | 1.1 | % |
Modeling Shrinkage | 流量 | ISO 294-4 | 0.30 | % |
Moisture Absorption | Saturation, 23°C, 2.00 mm | ISO 62 | 6.4 | % |
Moisture Absorption | Equilibrium, 23°C, 2.00 mm, 50% RH | ISO 62 | 2.0 | % |
Flow Length | 2.00 mm | | 350 | mm |
Viscosity number | | ISO 307 | 150 | cm³/g |
Mechanical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Flexural Stress | | ISO 178 | 260 | Mpa |
Tensile Stress | Break | ISO 527-2 | 180 | Mpa |
Tensile Strain | Break | ISO 527-2 | 3.0 | % |
Tensile Modulus | | ISO 527-2 | 8500 | Mpa |
Flexural Modulus | | ISO 178 | 8000 | Mpa |
Thermal Properties | Test Condition | Test Method | Test Result | Unit |
---|
Deflection Temperature Under Load? | 0.45 MPa, Unannealed | ISO 75-2/B | 261 | °C |
Deflection Temperature Under Load? | 1.8 MPa, Unannealed | ISO 75-2/A | 252 | °C |
Vicat Softening Temperature | | ISO 306/B50 | 257 | °C |
Linear thermal expansion coefficient | Flow | ISO 11359-2 | 3.3E-5 | cm/cm/°C |
Linear thermal expansion coefficient | Across Flow | ISO 11359-2 | 1.1E-4 | cm/cm/°C |
Glass Transition Temperature | | ISO 11357-2 | 80.0 | °C |
Melting Temperature | | ISO 11357-3 | 262 | °C |
Electrical performance | Test Condition | Test Method | Test Result | Unit |
---|
Relative Permittivity | 100 Hz | IEC 62631-2-1 | 3.60 | |
Comparative Tracking Index | | IEC 60112 | 400 | V |
Dissipation Factor? | 100 Hz | IEC 62631-2-1 | 7.0E-3 | |
Surface Resistivity | | IEC 62631-3-2 | -- | ohms |
Volume Resistivity | | IEC 62631-3-1 | 1.0E+13 | ohms·m |
Fill Analysis | Test Condition | Test Method | Test Result | Unit |
---|
Melt Density | | | 1.15 | g/cm³ |
Ejection Temperature | | | 210 | °C |
Specific Heat Capacity of Melt | | | 2090 | J/kg/°C |
Thermal Conductivity of Melt | | | 0.21 | W/m/K |
Odor | | VDA 270 | 3.50 | |
Injection | Test Condition | Test Method | Test Result | Unit |
---|
Drying Temperature | | | 80 | °C |
Drying time - Hot air dryer | | | 2.0 到 4.0 | hr |
Suggested Max Moisture | | | 0.20 | % |
Processing (Melt) Temp | | | 285 到 305 | °C |
Melt Temperature, Optimum | | | 295 | °C |
Mold Temperature | | | 70 到 120 | °C |
Mold Temperature, Optimum | | | 100 | °C |
Holding Pressure | | | 50.0 到 100 | Mpa |
Holding Pressure | Drying Recommended | | yes | |
Hold Pressure Time | | | 3.00 | s/mm |
Maximum Screw Tangential Speed | | | 12 | m/min |
Impact Properties | Test Condition | Test Method | Test Result | Unit |
---|
Charpy Unnotched Impact Strength | -30°C | ISO 179/1eU | 60 | kJ/m² |
Charpy Unnotched Impact Strength | 23°C | ISO 179/1eU | 60 | kJ/m² |
hardness | Test Condition | Test Method | Test Result | Unit |
---|
Ball Indentation Hardness | H 961/30 | ISO 2039-1 | 260 | Mpa |
Flammability | Test Condition | Test Method | Test Result | Unit |
---|
Burning Rate | 1.00 mm | ISO 3795 | 26 | mm/min |
Flame Rating | 1.5 mm | UL 94, IEC 60695-11-10, -20 | HB | |
Flame Rating | 3.0 mm | UL 94, IEC 60695-11-10, -20 | HB | |
FMVSS Flammability | | FMVSS 302 | B | |
Haze | | ISO 6452 | 5.0E-4 | g |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.