PBT VALOX™ 310SEO-1001 SABIC INNOVATIVE JAPAN

Unit Price:
$4082 USD/MT
Packaging Specification:
25KG/PKG
Supply Quantity:
50MT
Delivery Terms:
FOB
Port of Loading:
China Main Port
Accepted Payment Methods:
T/T
Shipping:
Negotiate supplier for shipping details

Supplier Information

ASIA PLASTIC EXCHANGE LIMITED

serv********

For more detailed information including pricing, customization, and shipping, please contact supplier.

Technical Data Sheet

Physical Properties	Test Condition	Test Method	Test Result	Unit
Modeling Shrinkage	MD：--2	内部方法	0.90to1.6	%
	Modeling Shrinkage	MD：--3	内部方法	1.5to2.3	%
		Modeling Shrinkage	TD：--2	内部方法	1.0to1.7	%
			Modeling Shrinkage	TD：--3	内部方法	1.6to2.4	%
				Modeling Shrinkage	Flow 2	内部方法	1.1 到 1.8	%
					Modeling Shrinkage	Flow : 0.750 to 2.30 mm	内部方法	0.90 到 1.6	%
						Modeling Shrinkage	Flow : 3.20 mm	内部方法	1.5 到 2.3	%
							Modeling Shrinkage	Flow : 2.30 to 4.60 mm	内部方法	1.5 到 2.3	%
								Modeling Shrinkage	Across Flow 2	内部方法	0.90 到 1.9	%
									Modeling Shrinkage	Across Flow : 0.750 to 2.30 mm	内部方法	1.0 到 1.7	%
									Modeling Shrinkage	Modeling Shrinkage	Across Flow : 2.30 to 4.60 mm	内部方法	1.6 到 2.4	%
Moisture Absorption	Saturation, 23°C	ISO 62	0.36	%
	Moisture Absorption	Equilibrium, 23°C, 50% RH	ISO 62	0.080	%
	Moisture Absorption	Moisture Absorption	24hr	ASTMD570	0.080	%
Melt Viscosity		内部方法	600	Pa·s
Melt Mass-Flow Rate	250°C/2.16 kg	ASTM D1238	8.6	g/10 min
Melt Volume flow Rate	250°C/2.16 kg	ISO 1133	8.00	cm3/10min
Specific Volume		ASTMD792	0.770	cm³/g
Specific Volume	Specific Volume		ASTM D792	0.710	cm³/g

Mechanical Properties	Test Condition	Test Method	Test Result	Unit
Flexural Modulus	50.0mmSpan	ASTMD790	2340	Mpa
Flexural Strength	Yield,50.0mmSpan	ASTMD790	82.7	Mpa
Flexural Strength	Flexural Strength	Break,50.0mmSpan	ASTMD790	82.7	Mpa
Tensile Strength	Yield	ASTMD638	51.7	Mpa
Tensile Strength	Break	ASTMD638	51.7	Mpa
Tensile Elongation	Break	ASTMD638	300	%
Tensile Strength	Yield 4	ASTM D638	58.0	Mpa
	Tensile Strength	Yield	ISO 527-2/50	58.0	Mpa
		Tensile Strength	Break 4	ASTM D638	52.0	Mpa
		Tensile Strength	Tensile Strength	Break	ISO 527-2/50	40.0	Mpa
Flexural Stress	-- 6, 7	ISO 178	90.0	Mpa
Flexural Stress	Flexural Stress	Yield, 50.0 mm Span 5	ASTM D790	101	Mpa
Taber Abrasion Resistance	1000 Cycles, 1000 g, CS-17 Wheel	内部方法	19.0	mg
Tensile Modulus	-- 3	ASTM D638	2820	Mpa
Tensile Modulus	Tensile Modulus	--	ISO 527-2/1	2800	Mpa
Tensile Elongation	Yield 4	ASTM D638	5.0	%
	Tensile Elongation	Yield	ISO 527-2/50	5.0	%
		Tensile Elongation	Break 4	ASTM D638	18	%
		Tensile Elongation	Tensile Elongation	Break	ISO 527-2/50	18	%
Flexural Modulus	50.0 mm Span 5	ASTM D790	2620	Mpa
Flexural Modulus	Flexural Modulus	-- 6	ISO 178	2600	Mpa

Thermal Properties	Test Condition	Test Method	Test Result	Unit
Deflection Temperature Under Load?	0.45MPa,Unannealed,6.40mm	ASTMD648	154	°C
Deflection Temperature Under Load?	Deflection Temperature Under Load?	1.8MPa,Unannealed,6.40mm	ASTMD648	54.4	°C
Linear thermal expansion coefficient	MD：-40to40°C	ASTME831	8.1E-05	cm/cm/°C
	Linear thermal expansion coefficient	MD：60to138°C	ASTME831	1.4E-04	cm/cm/°C
		Linear thermal expansion coefficient	Flow : -40 to 40°C	ASTM E831	7.9E-5	cm/cm/°C
			Linear thermal expansion coefficient	Flow : 60 to 138°C	ASTM E831	1.3E-4	cm/cm/°C
				Linear thermal expansion coefficient	Flow : -40 to 40°C	ISO 11359-2	7.6E-5	cm/cm/°C
					Linear thermal expansion coefficient	Flow : 23 to 60°C	ISO 11359-2	1.0E-4	cm/cm/°C
						Linear thermal expansion coefficient	Across Flow : -40 to 40°C	ASTM E831	7.9E-5	cm/cm/°C
							Linear thermal expansion coefficient	Across Flow : -40°C	ISO 11359-2	7.3E-5	cm/cm/°C
							Linear thermal expansion coefficient	Linear thermal expansion coefficient	Across Flow : 23 to 60°C	ISO 11359-2	1.0E-4	cm/cm/°C
RTIElec		UL746	120	°C
Evolution Calendar intelligent importer		UL746	120	°C
RTIStr		UL746	140	°C
Vicat Softening Temperature	--	ASTM D152511, ISO 306/B50, ISO 306/B120	170	°C
Vicat Softening Temperature	Vicat Softening Temperature	--	ISO 306/A50	212	°C
Thermal Conductivity		ISO 8302	0.24	W/m/K
RTI		UL 746	140	°C
RTI Imp		UL 746	120	°C
RTI Elec		UL 746	120	°C
Deflection Temperature Under Load?	0.45 MPa, Unannealed, 6.40 mm	ASTM D648	162	°C
	Deflection Temperature Under Load?	0.45 MPa, Unannealed, 4.00 mm, 100 mm Span 10	ISO 75-2/Be	150	°C
		Deflection Temperature Under Load?	1.8 MPa, Unannealed, 3.20 mm	ASTM D648	74.0	°C
			Deflection Temperature Under Load?	1.8 MPa, Unannealed, 6.40 mm	ASTM D648	71.0	°C
				Deflection Temperature Under Load?	1.8 MPa, Unannealed, 4.00 mm, 100 mm Span 10	ISO 75-2/Ae	60.0	°C
				Deflection Temperature Under Load?	Deflection Temperature Under Load?	1.8 MPa, Unannealed, 4.00 mm, 64.0 mm Span 9	ISO 75-2/Af	73.0	°C
Ball PressureTest	123 to 127°C	IEC 60695-10-2	通过

Electrical performance	Test Condition	Test Method	Test Result	Unit
Comparative Tracking Index		UL 746	PLC 3
Hot-wire Ignition		UL 746	PLC 2
Arc Resistance		ASTM D495	PLC 6
High Amp Arc Ignition		UL 746	PLC 0
High Voltage Arc Tracking Rate		UL 746	PLC 6
High Voltage Arc Tracking Rate		UL 746	PLC 4
High Voltage Arc Tracking Rate	HVTR	UL746	PLC1
Arc Resistance		ASTMD495	PLC5
Relative Permittivity	50 Hz	IEC 60250	2.90
	Relative Permittivity	60 Hz	IEC 60250	2.90
		Relative Permittivity	100 Hz	IEC 60250	3.10
		Relative Permittivity	Relative Permittivity	1 MHz	IEC 60250	2.80
Comparative Tracking Index	--	IEC 60112	175	V
Comparative Tracking Index	Comparative Tracking Index	Solution B	IEC 60112	100	V
Comparative Tracking Index	CTI	UL746	PLC0
Dielectric Strength	1.60mm,inAir	ASTMD149	23	KV/mm
	Dielectric Strength	1.60mm,in Oil	ASTMD149	23	KV/mm
		Dielectric Strength	3.20mm,inAir	ASTMD149	16	KV/mm
			Dielectric Strength	3.20mm,in Oil	ASTMD149	16	KV/mm
				Dielectric Strength	1.60 mm, in Oil	ASTM D149	24	KV/mm
					Dielectric Strength	3.20 mm, in Air	ASTM D149	18	KV/mm
						Dielectric Strength	0.800 mm, in Oil	IEC 60243-1	35	KV/mm
							Dielectric Strength	1.00 mm 12	IEC 60243-1	18	KV/mm
								Dielectric Strength	1.60 mm, in Oil	IEC 60243-1	25	KV/mm
								Dielectric Strength	Dielectric Strength	3.20 mm, in Oil	IEC 60243-1	17	KV/mm
Dissipation Factor?	100Hz	ASTMD150	2E-03
	Dissipation Factor?	1MHz	ASTMD150	0.020
		Dissipation Factor?	50 Hz	IEC 60250	1.0E-3
			Dissipation Factor?	60 Hz	IEC 60250	1.0E-3
				Dissipation Factor?	100 Hz	IEC 60250	2.0E-3
				Dissipation Factor?	Dissipation Factor?	1 MHz	IEC 60250	0.013
Surface Resistivity		IEC 60093	> 1.0E+15	ohms
Dielectric Constant	100Hz	ASTMD150	3.30
Dielectric Constant	Dielectric Constant	1MHz	ASTMD150	3.10
Volume Resistivity		IEC 60093	> 1.0E+15	ohms·cm
Volume Resistivity	Volume Resistivity		ASTMD257	>4.0E+16	ohms·cm

Injection	Test Result	Unit
Drying Temperature	120	°C
Suggested Max Moisture	0.020	%
Processing (Melt) Temp	245 到 260	°C
Mold Temperature	50 到 75	°C
Drying Time	3.0 到 4.0	hr
Suggested Shot Size	40 到 80	%
Rear Temperature	230 到 250	°C
Middle Temperature	240 到 255	°C
Front Temperature	245 到 260	°C
Nozzle Temperature	240 到 255	°C
Back Pressure	0.300 到 0.700	Mpa
Screw Speed	50 到 100	rpm
Vent Depth	0.013 到 0.025	mm

Impact Properties	Test Condition	Test Method	Test Result	Unit
Gardner Impact	23°C	ASTMD3029	40.7	J
Gardner Impact	Gardner Impact	23°C6	ASTMD3029	40.7	J
Instrumented Dart Impact	23°C, Total Energy	ASTM D3763	200	J
Charpy Unnotched Impact Strength	-30°C	ISO 179/1eU	无断裂
Charpy Unnotched Impact Strength	Charpy Unnotched Impact Strength	23°C	ISO 179/1eU	无断裂
Unnotched Izod Impact Strength	23°C	ASTM D4812, ISO 180/1U	无断裂
Unnotched Izod Impact Strength	Unnotched Izod Impact Strength	-30°C 9	ISO 180/1U	无断裂

hardness	Test Condition	Test Method	Test Result	Unit
Rockwell Hardness	R-Scale	ASTMD785	117
Rockwell Hardness	Rockwell Hardness	R -Sale	ISO 2039-2	120
Ball Indentation Hardness	H 358/30	ISO 2039-1	105	Mpa

Flammability	Test Condition	Test Method	Test Result	Unit
UL flame retardant rating	1.5mm	UL94	HB
Glow Wire Flammability Index	1.0 mm	IEC 60695-2-12	960	°C
Oxygen Index		ISO 4589-2	30	%
Flame Rating	0.71 mm	UL 94	V-0
Flame Rating	Flame Rating	3.0 mm	UL 94	5VA

IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.