Technical Data Sheet
Physical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Modeling Shrinkage | Across Flow | ISO 294-4 | 0.70 | % |
Modeling Shrinkage | 流量 | ISO 294-4 | 0.30 | % |
Moisture Absorption | Saturation, 23°C | ISO 62 | 4.3 到 5.3 | % |
Moisture Absorption | Equilibrium, 23°C, 50% RH | ISO 62 | 1.4 到 1.8 | % |
Apparent Density | | | 0.70 | g/cm³ |
Viscosity number | 96% H2SO4 | ISO 307 | 120 | cm³/g |
Melt Volume flow Rate | 325°C/5.0 kg | ISO 1133 | 45.0 | cm3/10min |
模具收缩性 - model-housing | 1.50 mm | | 0.10 | % |
Mechanical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Tensile Stress | Break | ISO 527-2 | 150 | Mpa |
Tensile Strain | Break | ISO 527-2 | 2.5 | % |
Tensile Modulus | | ISO 527-2 | 11000 | Mpa |
Flexural Modulus | | ISO 178 | 11000 | Mpa |
Flexural Stress | | ISO 178 | 240 | Mpa |
Thermal Properties | Test Condition | Test Method | Test Result | Unit |
---|
Melting temperature | | ISO 11357-3 | 290 | °C |
Deflection Temperature Under Load? | 1.8 MPa, Unannealed | ISO 75-2/A | 220 | °C |
Electrical performance | Test Condition | Test Method | Test Result | Unit |
---|
Surface Resistivity | | IEC 60093 | -- | ohms |
Volume Resistivity | | IEC 60093 | 1.0E+17 | ohms·cm |
Dissipation Factor? | 1 MHz | IEC 60250 | 0.015 | |
Relative Permittivity | 1 MHz | IEC 60250 | 3.90 | |
Comparative Tracking Index | Solution A | IEC 60112 | 600 | V |
Injection | Test Condition | Test Method | Test Result | Unit |
---|
Drying Time | | | 8.0 | hr |
Rear Temperature | | | 300 | °C |
Middle Temperature | | | 310 | °C |
Front Temperature | | | 320 | °C |
Nozzle Temperature | | | 320 | °C |
Hopper Temperature | | | 80 | °C |
Residence Time | | | < 5.0 | min |
Screw Speed | | | < 18 | m/min |
Drying Temperature | | | 110 | °C |
Suggested Max Moisture | | | 0.030 | % |
Processing (Melt) Temp | | | 310 到 330 | °C |
Mold Temperature | | | 80 到 120 | °C |
Impact Properties | Test Condition | Test Method | Test Result | Unit |
---|
Charpy Unnotched Impact Strength | -30°C | ISO 179/1eU | 65 | kJ/m² |
Charpy Unnotched Impact Strength | 23°C | ISO 179/1eU | 65 | kJ/m² |
Flammability | Test Condition | Test Method | Test Result | Unit |
---|
Polymer Abbreviation | | | PA6T/6-GF30 FR | |
Glow Wire Flammability Index | 0.40 mm | IEC 60695-2-12 | 960 | °C |
Oxygen Index | | ISO 4589-2 | 50 | % |
Glow Wire Ignition Temperature | 0.40 mm | IEC 60695-2-13 | 775 | °C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.