Technical Data Sheet
Physical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Modeling Shrinkage | Flow : 24hr | ASTM D955 | 1.4 | % |
Modeling Shrinkage | Across Flow : 24hr | ASTM D955 | 1.6 | % |
Modeling Shrinkage | Across Flow : 24hr | ISO 294-4 | 1.3 | % |
Modeling Shrinkage | 流量 : 24hr | ISO 294-4 | 1.5 | % |
Moisture Absorption | 24 hr, 50% RH | ASTM D570 | 0.16 | % |
Moisture Absorption | Equilibrium, 23°C, 50% RH | ISO 62 | 0.29 | % |
Mechanical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Tensile Modulus | -- 1 | ASTM D638 | 6130 | Mpa |
Tensile Modulus | -- | ISO 527-2/1 | 5800 | Mpa |
Tensile Elongation | Yield | ASTM D638 | 3.6 | % |
Tensile Elongation | Yield | ISO 527-2 | 2.3 | % |
Tensile Elongation | Break | ASTM D638 | 2.6 | % |
Tensile Elongation | Break | ISO 527-2 | 4.0 | % |
Flexural Modulus | -- | ASTM D790 | 5300 | Mpa |
Flexural Modulus | -- | ISO 178 | 6300 | Mpa |
Flexural Strength | | ASTM D790, ISO 178 | 92.0 | Mpa |
Tensile Strength | Yield | ASTM D638 | 56.0 | Mpa |
Tensile Strength | Yield | ISO 527-2 | 49.0 | Mpa |
Tensile Strength | Break | ASTM D638 | 56.0 | Mpa |
Tensile Strength | Break | ISO 527-2 | 46.0 | Mpa |
Coefficient of Friction | Dynamic | ASTM D3702 | 0.50 | |
Coefficient of Friction | Static | ASTM D3702 | 0.43 | |
Specific Wear Rate | | ASTM D3702 | 1.9E+8 | 10^-8 mm³/N·m |
Thermal Properties | Test Condition | Test Method | Test Result | Unit |
---|
Deflection Temperature Under Load? | 0.45 MPa, Unannealed, 3.20 mm | ASTM D648 | 161 | °C |
Deflection Temperature Under Load? | 1.8 MPa, Unannealed, 3.20 mm | ASTM D648 | 132 | °C |
Deflection Temperature Under Load? | 1.8 MPa, Unannealed, 4.00 mm, 64.0 mm Span 3 | ISO 75-2/Af | 147 | °C |
Injection | Test Condition | Test Method | Test Result | Unit |
---|
Drying Time | | | 4.0 | hr |
Rear Temperature | | | 175 到 190 | °C |
Middle Temperature | | | 195 到 205 | °C |
Front Temperature | | | 210 到 220 | °C |
Back Pressure | | | 0.200 到 0.300 | Mpa |
Screw Speed | | | 30 到 60 | rpm |
Drying Temperature | | | 80 | °C |
Processing (Melt) Temp | | | 200 到 215 | °C |
Mold Temperature | | | 80 到 110 | °C |
Impact Properties | Test Condition | Test Method | Test Result | Unit |
---|
Unnotched Izod Impact Strength | 23°C | ASTM D4812 | 210 | J/m |
Unnotched Izod Impact Strength | 23°C 3 | ISO 180/1U | 17 | kJ/m² |
Instrumented Dart Impact | 23°C, Energy at Peak | ASTM D3763 | 9.00 | J |
Instrumented Dart Impact | -- | ISO 6603-2 | 2.00 | J |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.