Technical Data Sheet
Physical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Specific Volume | | ASTMD792 | 0.802 | cm³/g |
Melt Mass-Flow Rate | | ASTMD1238 | 10to15 | g/10min |
Melt Mass-Flow Rate | | ISO1133 | 16 | g/10min |
Modeling Shrinkage | MD | ASTMD955 | 2.0 | % |
Modeling Shrinkage | TD | ISO294-4 | 1.7to2.2 | % |
Modeling Shrinkage | MD | ISO294-4 | 1.7to2.2 | % |
Mechanical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Tensile Modulus | 23°C | ASTMD638 | 635 | Mpa |
Tensile Modulus | | ISO527-2/1A/1 | 500 | Mpa |
Flexural Modulus | 23°C | ISO178 | 450 | Mpa |
Flexural Stress | 23°C | ISO178 | 22.0 | Mpa |
Tab | 1000Cycles,CS-18Wheel | ASTMD4060 | 30.0 | mg |
RossFlex | | 内部方法 | >1.0E+6 | cycles |
Tensile Stress | Yield | ISO527-2/1A/50 | 28.0 | Mpa |
Tensile Strength | Break,23°C | ASTMD638 | 29.2 | Mpa |
Tensile Stress | Break | ISO527-2 | 40.0 | Mpa |
Tensile Stress | 5.0%Strain | ISO527-2 | 21.0 | Mpa |
Tensile Stress | 10%Strain | ISO527-2 | 27.0 | Mpa |
Tensile Stress | 50%Strain | ISO527-2 | 25.0 | Mpa |
Tensile Strain | Yield | ISO527-2/1A/50 | 19 | % |
Tensile Elongation | Break,23°C | ASTMD638 | 300 | % |
Nominal Tensile Strain at Break | | ISO527-2/1A/50 | >50 | % |
Flexural Modulus | -40°C | ISO178 | 2400 | Mpa |
Thermal Properties | Test Condition | Test Method | Test Result | Unit |
---|
Vicat Softening Temperature | | ASTMD1525 | 204 | °C |
Peak Melting Temperature | | ASTMD3418 | 214 | °C |
Melting Temperature | | ISO11357-3 | 215 | °C |
Linear thermal expansion coefficient | MD | ASTMD696 | 1.7E-04 | cm/cm/°C |
Linear thermal expansion coefficient | MD | ISO11359-2 | 1.4E-04 | cm/cm/°C |
Deflection Temperature Under Load? | 0.45MPa,Unannealed | ISO75-2/B | 118 | °C |
Glass Transition Temperature | | ASTMD3418 | -23.3 | °C |
Electrical performance | Test Condition | Test Method | Test Result | Unit |
---|
Surface Resistivity | | IEC60093 | 2E+17 | ohms |
Dielectric Strength | | IEC60243-1 | 28 | KV/mm |
Relative Permittivity | 1MHz | IEC60250 | 3.70 | |
Dissipation Factor? | 1MHz | IEC60250 | 0.040 | |
Comparative Tracking Index | | IEC60112 | >600 | V |
Elastomers Properties | Test Condition | Test Method | Test Result | Unit |
---|
TearStrength-Flow3 | | ISO34-1 | 190 | kN/m |
Compression Set | 23°C | ASTMD395 | <1.0 | % |
Shore Hardness | -- | 内部方法 | 40 | % |
Shore Hardness | -- | ASTMD2632 | 40 | % |
Impact Properties | Test Condition | Test Method | Test Result | Unit |
---|
Charpy Unnotched Impact Strength | -30°C | ISO179/1eU | NoBreak | |
Charpy Unnotched Impact Strength | 23°C | ISO179/1eU | NoBreak | |
hardness | Test Condition | Test Method | Test Result | Unit |
---|
Shore Hardness | Shore D | ASTMD2240 | 72 | |
Shore Hardness | Shore D,15sec | ISO868 | 72 | |
Flammability | Test Condition | Test Method | Test Result | Unit |
---|
UL flame retardant rating | 1.5mm | UL94 | HB | |
Supplementary information | Test Condition | Test Method | Test Result | Unit |
---|
Tearing Strength | | Kg/m | 217.2 | kN/m |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.