Technical Data Sheet
Physical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Melt Mass-Flow Rate | 240°C/2.16kg | ISO1133 | 19 | g/10min |
Modeling Shrinkage | MD | ASTMD955 | 1.9 | % |
Modeling Shrinkage | TD | ISO294-4 | 1.7to2.1 | % |
Modeling Shrinkage | MD | ISO294-4 | 1.7to2.0 | % |
Specific Volume | | ASTMD792 | 0.820 | cm³/g |
Melt Mass-Flow Rate | | ASTMD1238 | 16 | g/10min |
Mechanical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Tensile Modulus | 23°C | ASTMD638 | 365 | Mpa |
Tensile Modulus | | ISO527-2/1A/1 | 350 | Mpa |
Tensile Stress | Yield | ISO527-2/1A/50 | 22.0 | Mpa |
Tensile Strength | Break,23°C | ASTMD638 | 26.2 | Mpa |
Tensile Stress | Break | ISO527-2/1A/50 | 38.0 | Mpa |
Tensile Stress | 5.0%Strain | ISO527-2 | 13.0 | Mpa |
Tensile Stress | 10%Strain | ISO527-2 | 18.0 | Mpa |
Tensile Stress | 50%Strain | ISO527-2/1A/50 | 21.0 | Mpa |
Tensile Strain | Yield | ISO527-2/1A/50 | 44 | % |
Tensile Elongation | Break,23°C | ASTMD638 | 320 | % |
Nominal Tensile Strain at Break | | ISO527-2/1A/50 | >50 | % |
Flexural Modulus | -40°C | ISO178 | 1900 | Mpa |
Flexural Modulus | 23°C | ISO178 | 325 | Mpa |
Flexural Stress | 23°C | ISO178 | 17.5 | Mpa |
RossFlex | | 内部方法 | >1.0E+6 | cycles |
Thermal Properties | Test Condition | Test Method | Test Result | Unit |
---|
Linear thermal expansion coefficient | MD | ISO11359-2 | 1.8E-04 | cm/cm/°C |
Deflection Temperature Under Load? | 0.45MPa,Unannealed | ISO75-2/B | 114 | °C |
Glass Transition Temperature | | ASTMD3418 | -42.8 | °C |
Vicat Softening Temperature | | ASTMD1525 | 195 | °C |
Peak Melting Temperature | | ASTMD3418 | 210 | °C |
Melting Temperature | | ISO11357-3 | 212 | °C |
Electrical performance | Test Condition | Test Method | Test Result | Unit |
---|
Surface Resistivity | | IEC60093 | 1E+16 | ohms |
Volume Resistivity | | ASTMD257 | 2E+13 | ohms·cm |
Volume Resistivity | | IEC60093 | 2E+15 | ohms·cm |
Dielectric Strength | | ASTMD149 | 13 | KV/mm |
Dielectric Strength | | IEC60243-1 | 14 | KV/mm |
Relative Permittivity | 1MHz | IEC60250 | 4.00 | |
Dissipation Factor? | 1MHz | IEC60250 | 0.040 | |
Comparative Tracking Index | | ASTMD3638 | >600 | V |
Comparative Tracking Index | | IEC60112 | >600 | V |
Elastomers Properties | Test Condition | Test Method | Test Result | Unit |
---|
TearStrength-Flow2 | | ISO34-1 | 160 | kN/m |
Compression Set | 23°C | ASTMD395 | <1.0 | % |
Shore Hardness | -- | 内部方法 | 40 | % |
Shore Hardness | -- | ASTMD2632 | 40 | % |
Impact Properties | Test Condition | Test Method | Test Result | Unit |
---|
Charpy Unnotched Impact Strength | -30°C | ISO179/1eU | NoBreak | |
Charpy Unnotched Impact Strength | 23°C | ISO179/1eU | NoBreak | |
hardness | Test Condition | Test Method | Test Result | Unit |
---|
Shore Hardness | Shore D | ASTMD2240 | 63 | |
Shore Hardness | Shore D,15sec | ISO868 | 63 | |
Flammability | Test Condition | Test Method | Test Result | Unit |
---|
UL flame retardant rating | 1.5mm | UL94 | HB | |
Supplementary information | Test Condition | Test Method | Test Result | Unit |
---|
Tearing Strength | | Kg/m | 269.7 | kN/m |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.