Technical Data Sheet
Physical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Modeling Shrinkage | MD1 | 内部方法 | 1.2到1.4 | % |
Moisture Absorption | Saturation,23°C | ISO62 | 0.12 | % |
Melt Volume flow Rate | 320°C/2.16kg | ISO1133 | 8.00 | cm3/10min |
Mechanical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Flexural Stress | --4 | ISO178 | 18.0 | Mpa |
Flexural Stress | --5 | ISO178 | 20.0 | Mpa |
Taber Abrasion Resistance | 1000Cycles,1000g,CS-17Wheel | 内部方法 | 60.0 | mg |
Tensile Stress | Yield | ISO527-2/50 | 20.0 | Mpa |
Tensile Stress | Break | ISO527-2/50 | 25.0 | Mpa |
Tensile Strain | Yield | ISO527-2/50 | 15 | % |
Tensile Strain | Break | ISO527-2/50 | 110 | % |
Tensile Modulus | | ISO527-2/1 | 590 | Mpa |
Flexural Modulus | | ISO178 | 475 | Mpa |
Thermal Properties | Test Condition | Test Method | Test Result | Unit |
---|
-- | | ISO306/B50 | 75.0 | °C |
-- | | ISO306/B120 | 78.0 | °C |
Linear thermal expansion coefficient | MD:23to80°C | ISO11359-2 | 1.1E-04 | cm/cm/°C |
Linear thermal expansion coefficient | TD:23to80°C | ISO11359-2 | 9E-05 | cm/cm/°C |
Ball PressureTest | 75°C | IEC60695-10-2 | Pass | |
Electrical performance | Test Condition | Test Method | Test Result | Unit |
---|
Relative Permittivity | 100Hz | IEC60250 | 3.00 | |
Comparative Tracking Index | -- | IEC60112 | 175 | V |
Comparative Tracking Index | SolutionB | IEC60112 | 100 | V |
Surface Resistivity | | IEC60093 | >1.0E+15 | ohms |
Volume Resistivity | | IEC60093 | 4.7E+14 | ohms·cm |
Dissipation Factor? | 100Hz | IEC60250 | 9.1E-03 | |
Dielectric Strength | 3.20mm,in Oil | IEC60243-1 | 19 | KV/mm |
Impact Properties | Test Condition | Test Method | Test Result | Unit |
---|
Notched Izod Impact Strength | -30°C | ISO180/1A | 15 | kJ/m² |
Notched Izod Impact Strength | 23°C | ISO180/1A | 25 | kJ/m² |
Unnotched Izod Impact Strength | -30°C | ISO180/1U | 无断裂 | |
Unnotched Izod Impact Strength | 23°C | ISO180/1U | 无断裂 | |
Flammability | Test Condition | Test Method | Test Result | Unit |
---|
UL flame retardant rating | 1.60mm,TestingbySABIC | UL94 | V-1 | |
Glow Wire Flammability Index | 3.20mm | IEC60695-2-12 | 960 | °C |
Oxygen Index | | ISO4589-2 | 48 | % |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.