Technical Data Sheet
Physical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Moisture Absorption | Saturation, 23°C | ISO 62 | 3.5 到 4.5 | % |
Moisture Absorption | Equilibrium, 23°C, 50% RH | ISO 62 | 0.40 到 0.80 | % |
Modeling Shrinkage | Across Flow | ISO 294-4 | 0.66 | % |
Modeling Shrinkage | 流量 | ISO 294-4 | 0.20 | % |
Apparent Density | | | 0.70 | g/cm³ |
Viscosity number | 96% H2SO4 | ISO 307 | 135 | cm³/g |
Modeling Shrinkage | | | 0.29 | % |
Mechanical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Tensile Creep Modulus | 1000 hr | ISO 899-1 | -- | Mpa |
Tensile Stress | Break | ISO 527-2 | 240 | Mpa |
Tensile Strain | Break | ISO 527-2 | 2.4 | % |
Tensile Modulus | | ISO 527-2 | 17000 | Mpa |
Thermal Properties | Test Condition | Test Method | Test Result | Unit |
---|
Deflection Temperature Under Load? | 1.8 MPa, Unannealed | ISO 75-2/A | 245 | °C |
Specific Heat | | | 1000 | J/kg/°C |
Thermal Conductivity | | DIN 52612 | 0.32 | W/m/K |
Linear thermal expansion coefficient | Flow : 23 to 55°C | ISO 11359-2 | 1.8E-5 | cm/cm/°C |
Linear thermal expansion coefficient | Across Flow : 23 to 55°C | ISO 11359-2 | 5.0E-5 到 6.0E-5 | cm/cm/°C |
Melting temperature | | ISO 11357-3 | 285 | °C |
Maximum Service Temperature (short cycle operation) | | | 260 | °C |
Temperature Index | -- 5 | IEC 60216 | 170 | °C |
Temperature Index | -- 6 | IEC 60216 | 145 | °C |
Electrical performance | Test Condition | Test Method | Test Result | Unit |
---|
Dissipation Factor? | 1 MHz | IEC 60250 | 0.020 | |
Dielectric Strength | | IEC 60243-1 | 33 | KV/mm |
Relative Permittivity | 1 MHz | IEC 60250 | 4.70 | |
Comparative Tracking Index | Solution A | IEC 60112 | 600 | V |
Surface Resistivity | | IEC 60093 | -- | ohms |
Volume Resistivity | | IEC 60093 | 1.0E+17 | ohms·cm |
Injection | Test Condition | Test Method | Test Result | Unit |
---|
Residence Time | | | < 5.0 | min |
Screw Speed | | | < 18 | m/min |
Drying Temperature | | | 110 | °C |
Suggested Max Moisture | | | 0.15 | % |
Processing (Melt) Temp | | | 310 到 330 | °C |
Mold Temperature | | | 80 到 120 | °C |
Drying Time | | | 8.0 | hr |
Rear Temperature | | | 300 | °C |
Middle Temperature | | | 310 | °C |
Front Temperature | | | 320 | °C |
Nozzle Temperature | | | 320 | °C |
Hopper Temperature | | | 80 | °C |
Impact Properties | Test Condition | Test Method | Test Result | Unit |
---|
Charpy Unnotched Impact Strength | -30°C | ISO 179/1eU | 85 | kJ/m² |
Charpy Unnotched Impact Strength | 23°C | ISO 179/1eU | 90 | kJ/m² |
Flammability | Test Condition | Test Method | Test Result | Unit |
---|
Polymer Abbreviation | | | PA6T/6-GF50 | |
Flammability level | 1.6 mm | IEC 60695-11-10, -20 | HB | |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.