Technical Data Sheet
Physical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Melt Volume flow Rate | 250°C/2.16kg | ISO1133 | 20.0 | cm3/10min |
Melt Volume flow Rate | 250°C/5.0kg | ISO1133 | 50.0 | cm3/10min |
Modeling Shrinkage | MD | 内部方法 | 2.0到2.6 | % |
Modeling Shrinkage | TD | 内部方法 | 0.90到1.8 | % |
Moisture Absorption | Saturation,23°C | ISO62 | 0.34 | % |
Moisture Absorption | Equilibrium,23°C,50%RH | ISO62 | 0.080 | % |
Mechanical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Flexural Modulus | | ISO178 | 2400 | Mpa |
yield | | ISO527-2/50 | 60.0 | Mpa |
yield | | ISO527-2/50 | 10 | % |
fracture | | ISO527-2/50 | 60.0 | Mpa |
fracture | | ISO527-2/50 | 15 | % |
Break | | ASTMD638 | 60.0 | Mpa |
--2 | | ASTMD638 | 2500 | Mpa |
Yield | | ASTMD638 | 60.0 | Mpa |
Break | | ASTMD638 | 15 | % |
Yield | | ASTMD638 | 7.0 | % |
Flexural Stress | | ISO178 | 85.0 | Mpa |
Thermal Properties | Test Condition | Test Method | Test Result | Unit |
---|
1.8MPa, Unannealed,64.0mm Span | | ISO75-2/Af | 50.0 | °C |
0.45MPa, Unannealed,3.20mm Span | | ISO75-2/Bf | 150 | °C |
-- | | ASTMD1525,ISO306/B50,ISO306/B12014 | 185 | °C |
-- | | ASTMD1525,ISO306/A501015 | 220 | °C |
Ball PressureTest | 125°C | IEC60695-10-2 | Pass | |
Fill Analysis | Test Condition | Test Method | Test Result | Unit |
---|
Melt Viscosity | 260°C,1500sec^-1 | ISO11443 | 165 | Pa·s |
Impact Properties | Test Condition | Test Method | Test Result | Unit |
---|
0°C10 | | ISO180/1A | 4.0 | kJ/m² |
23°C | | ASTMD256 | 38 | J/m |
23°C | | ASTMD4812,ISO180/1U | 无断裂 | |
-30°C12 | | ISO180/1U | 100 | kJ/m² |
-30°C | | ASTMD4812 | 无断裂 | |
-30°C | | ASTMD256 | 36 | J/m |
0°C | | ASTMD256 | 36 | J/m |
23°C11 | | ISO180/1A | 4.0 | kJ/m² |
-30°C9 | | ISO180/1A | 4.0 | kJ/m² |
Charpy Unnotched Impact Strength | -30°C | ISO179/2U | 80 | kJ/m² |
Charpy Unnotched Impact Strength | 23°C | ISO179/2U | 无断裂 | |
hardness | Test Condition | Test Method | Test Result | Unit |
---|
Rockwell Hardness | R-Sale | ISO2039-2 | 117 | |
Ball Indentation Hardness | H358/30 | ISO2039-1 | 145 | Mpa |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.