Technical Data Sheet
Physical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Density | | ASTM D792/ISO 1183 | 1.71 | |
Physical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Modeling Shrinkage | TD2 | ISO294-4 | 1.5 | % |
Modeling Shrinkage | TD | ISO294-4 | 1.2 | % |
Modeling Shrinkage | MD | ISO294-4 | 0.30 | % |
Modeling Shrinkage | MD2 | ISO294-4 | 0.50 | % |
Modeling Shrinkage | MD | ISO294-4 | 0.50 | % |
Modeling Shrinkage | MD2 | ISO294-4 | 0.60 | % |
Moisture Absorption | Saturation,23°C,2.00mm | ISO62 | 0.30 | % |
Moisture Absorption | Equilibrium,23°C,2.00mm,50%RH | ISO62 | 0.10 | % |
Moisture Absorption | Saturation,23°C,2.00mm | ISO62 | 0.32 | % |
Moisture Absorption | Equilibrium,23°C,2.00mm,50%RH | ISO62 | 0.13 | % |
MediumDensity | | | 1.49 | g/cm³ |
Ejection Temperature | | | 170 | °C |
Ejection Temperature | | | 170 | °C |
SpecificHeatCapacityofMelt | | | 1600 | J/kg/°C |
ThermalConductivityofMelt | | | 0.26 | W/m/K |
Mechanical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Tensile Stress | Break | ISO527-2 | 125 | Mpa |
Tensile Stress | Break | ISO527-2 | 110 | Mpa |
Tensile Strain | Break | ISO527-2 | 2.8 | % |
Tensile Strain | Break | ISO527-2 | 2.4 | % |
Tensile Modulus | | ISO527-2 | 11200 | Mpa |
Tensile Modulus | | ASTM D638/ISO 527 | 11200 | kg/cm²(MPa)[Lb/in²] |
Tensile Modulus | | ISO527-2 | 8300 | Mpa |
Flexural Strength | | ASTM D790/ISO 178 | 215 | kg/cm²(MPa)[Lb/in²] |
Tensile Creep Modulus | 1000hr | ISO899-1 | 8000 | Mpa |
Flexural Stress | | ISO178 | 215 | Mpa |
Flexural Stress | | ISO178 | 165 | Mpa |
Tensile Creep Modulus | 1hr | ISO899-1 | 11000 | Mpa |
Thermal Properties | Test Condition | Test Method | Test Result | Unit |
---|
Vicat Softening Temperature | | ISO306/B50 | 212 | °C |
Linear thermal expansion coefficient | MD | ISO11359-2 | 3E-05 | cm/cm/°C |
Linear thermal expansion coefficient | TD | ISO11359-2 | 9E-05 | cm/cm/°C |
Burning Rate | | UL94 | V-0 | |
Deflection Temperature Under Load? | 0.45MPa,Unannealed | ISO75-2/B | 220 | °C |
Deflection Temperature Under Load? | 1.8MPa,Unannealed | ISO75-2/A | 210 | °C |
Deflection Temperature Under Load? | 1.8MPa,Unannealed | ISO75-2/A | 200 | °C |
Melting Temperature | | ISO11357-3 | 225 | °C |
Electrical performance | Test Condition | Test Method | Test Result | Unit |
---|
Relative Permittivity | 1MHz | IEC60250 | 3.80 | |
Relative Permittivity | 100Hz | IEC60250 | 4.50 | |
Comparative Tracking Index | | IEC60112 | 250 | V |
Comparative Tracking Index | | IEC60112 | 225 | V |
Dielectric Strength | | IEC60243-1 | 39 | KV/mm |
Surface Resistivity | | IEC60093 | 1E+15 | ohms |
Volume Resistivity | | IEC60093 | >1.0E+15 | ohms·cm |
Dissipation Factor? | 100Hz | IEC60250 | 3E-03 | |
Dissipation Factor? | 1MHz | IEC60250 | 0.016 | |
Impact Properties | Test Condition | Test Method | Test Result | Unit |
---|
Notched Izod impact strength | -30°C | ISO180/1U | 40 | kJ/m² |
Notched Izod impact strength | 23°C | ISO180/1U | 40 | kJ/m² |
Charpy Unnotched Impact Strength | -30°C | ISO179/1eU | 57 | kJ/m² |
Charpy Unnotched Impact Strength | 23°C | ISO179/1eU | 53 | kJ/m² |
Charpy Unnotched Impact Strength | 23°C | ISO179/1eU | 50 | kJ/m² |
Flammability | Test Condition | Test Method | Test Result | Unit |
---|
UL flame retardant rating | 0.75mm | UL94 | V-0 | |
UL flame retardant rating | 1.5mm | UL94 | V-0 | |
UL flame retardant rating | 0.75mm | IEC60695-11-10,-20 | V-0 | |
UL flame retardant rating | 1.5mm | IEC60695-11-10,-20 | V-0 | |
UL flame retardant rating | 0.75mm | UL94 | V-0 | |
UL flame retardant rating | 1.5mm | UL94 | V-0 | |
UL flame retardant rating | 0.75mm | IEC60695-11-10,-20 | V-0 | |
UL flame retardant rating | 1.5mm | IEC60695-11-10,-20 | V-0 | |
Oxygen Index | | ISO4589-2 | 31 | % |
Oxygen Index | | ISO4589-2 | 32 | % |
FMVSS Flammability | | FMVSS302 | DNI | |
FMVSS Flammability | | FMVSS302 | DNI | |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.