Technical Data Sheet
Physical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Specific Volume | | ASTM D792 | 0.650 | cm³/g |
Melt Mass-Flow Rate | 266°C/5.0 kg | ASTM D1238 | 79 | g/10 min |
Modeling Shrinkage | Flow : 1.50 to 3.20 mm | 内部方法 | 0.40 到 0.60 | % |
Modeling Shrinkage | Flow : 3.20 to 4.60 mm | 内部方法 | 0.60 到 0.90 | % |
Modeling Shrinkage | Across Flow : 1.50 to 3.20 mm | 内部方法 | 0.50 到 0.80 | % |
Modeling Shrinkage | Across Flow : 3.20 to 4.60 mm | 内部方法 | 0.80 到 1.1 | % |
Moisture Absorption | 24 hr | ASTM D570 | 0.060 | % |
Mechanical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Tensile Strength | Break | ASTM D638 | 95.0 | Mpa |
Flexural Modulus | 50.0 mm Span | ASTM D790 | 5000 | Mpa |
Flexural Strength | Break, 50.0 mm Span | ASTM D790 | 143 | Mpa |
Thermal Properties | Test Condition | Test Method | Test Result | Unit |
---|
Deflection Temperature Under Load? | 0.45 MPa, Unannealed, 6.40 mm | ASTM D648 | 204 | °C |
Deflection Temperature Under Load? | 1.8 MPa, Unannealed, 6.40 mm | ASTM D648 | 187 | °C |
Coefficient of Linear Thermal Expansion (Flow) | -40 to 40°C | ASTM E831 | 4.0E-5 | cm/cm/°C |
Coefficient of Linear Thermal Expansion (Flow) | 60 to 138°C | ASTM E831 | 6.1E-5 | cm/cm/°C |
RTI Elec | | UL 746 | 125 | °C |
RTI Imp | | UL 746 | 110 | °C |
RTI | | UL 746 | 125 | °C |
Electrical performance | Test Condition | Test Method | Test Result | Unit |
---|
Volume Resistivity | | ASTM D257 | 1.0E+13 | ohms·cm |
Dielectric Strength | 1.60 mm, in Oil | ASTM D149 | 24 | KV/mm |
Dielectric Strength | 3.20 mm, in Air | ASTM D149 | 20 | KV/mm |
Dielectric Constant | 100 Hz | ASTM D150 | 3.50 | |
Dielectric Constant | 1 MHz | ASTM D150 | 3.30 | |
Dissipation Factor? | 100 Hz | ASTM D150 | 1.0E-3 | |
Dissipation Factor? | 1 MHz | ASTM D150 | 0.013 | |
Arc Resistance | | ASTM D495 | PLC 6 | |
Comparative Tracking Index | | UL 746 | PLC 3 | |
High Amp Arc Ignition | | UL 746 | PLC 4 | |
High Voltage Arc Tracking Rate | | UL 746 | PLC 4 | |
Hot-wire Ignition | | UL 746 | PLC 0 | |
Injection | Test Condition | Test Method | Test Result | Unit |
---|
Drying Temperature | | | 120 | °C |
Drying Time | | | 3.0 到 4.0 | hr |
Suggested Max Moisture | | | 0.020 | % |
Suggested Shot Size | | | 40 到 80 | % |
Rear Temperature | | | 240 到 255 | °C |
Middle Temperature | | | 245 到 260 | °C |
Front Temperature | | | 250 到 265 | °C |
Nozzle Temperature | | | 245 到 260 | °C |
Processing (Melt) Temp | | | 250 到 265 | °C |
Mold Temperature | | | 65 到 90 | °C |
Back Pressure | | | 0.300 到 0.700 | Mpa |
Screw Speed | | | 50 到 80 | rpm |
Vent Depth | | | 0.025 到 0.038 | mm |
Impact Properties | Test Condition | Test Method | Test Result | Unit |
---|
Unnotched Izod Impact Strength | 23°C | ASTM D4812 | 350 | J/m |
hardness | Test Condition | Test Method | Test Result | Unit |
---|
Rockwell Hardness | R-Scale | ASTM D785 | 119 | |
Flammability | Test Condition | Test Method | Test Result | Unit |
---|
Flame Rating | 1.5 mm | UL 94 | V-0 | |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.