Technical Data Sheet
Physical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Modeling Shrinkage | Across Flow | 内部方法 | 1.2 | % |
Modeling Shrinkage | 流量 | 内部方法 | 0.18 | % |
Moisture Absorption | Saturation | ASTM D570 | 0.020 | % |
Mechanical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Tensile Strength | | ASTM D638 | 147 | Mpa |
Tensile Elongation | Break | ASTM D638 | 5.2 | % |
Flexural Modulus | 23°C | ASTM D790 | 12300 | Mpa |
Flexural Modulus | 200°C | ASTM D790 | 4900 | Mpa |
Flexural Strength | 23°C | ASTM D790 | 143 | Mpa |
Flexural Strength | 200°C | ASTM D790 | 33.0 | Mpa |
Shearing Strength | | ASTM D732 | 51.0 | Mpa |
Poisson Ratio | | ASTM D785 | 0.46 | |
Thermal Properties | Test Condition | Test Method | Test Result | Unit |
---|
Deflection Temperature Under Load? | 1.8 MPa, Unannealed | ASTM D648 | 279 | °C |
Linear thermal expansion coefficient | Flow : 150°C | 内部方法 | 1.3E-5 | cm/cm/°C |
Linear thermal expansion coefficient | Across Flow : 150°C | 内部方法 | 5.6E-5 | cm/cm/°C |
Thermal Conductivity | | JIS R2618 | 0.52 | W/m/K |
Electrical performance | Test Condition | Test Method | Test Result | Unit |
---|
Volume Resistivity | | ASTM D257 | 1.0E+15 | ohms·cm |
Dielectric Constant | 1 kHz | ASTM D150 | 4.40 | |
Dielectric Constant | 1 MHz | ASTM D150 | 3.90 | |
Dissipation Factor? | 1 kHz | ASTM D150 | 0.022 | |
Dissipation Factor? | 1 MHz | ASTM D150 | 0.022 | |
Arc Resistance | | ASTM D495 | 130 | sec |
Comparative Tracking Index | | IEC 60112 | 125 | V |
Injection | Test Condition | Test Method | Test Result | Unit |
---|
Drying Temperature | | | 130 | °C |
Drying Time | | | 4.0 到 24 | hr |
Rear Temperature | | | 280 到 320 | °C |
Middle Temperature | | | 320 到 350 | °C |
Front Temperature | | | 340 到 370 | °C |
Nozzle Temperature | | | 340 到 370 | °C |
Processing (Melt) Temp | | | 360 | °C |
Mold Temperature | | | 40 到 160 | °C |
Injection Pressure | | | 80.0 到 160 | Mpa |
Injection Rate | | | 中等偏快 | |
Holding Pressure | | | 20.0 到 40.0 | Mpa |
Back Pressure | | | 1.00 到 5.00 | Mpa |
Screw Speed | | | 50 到 100 | rpm |
Impact Properties | Test Condition | Test Method | Test Result | Unit |
---|
Unnotched Izod Impact Strength | 6.40 mm | ASTM D256 | 410 | J/m |
hardness | Test Condition | Test Method | Test Result | Unit |
---|
Rockwell Hardness | R-Scale | ASTM D785 | 103 | |
Flammability | Test Condition | Test Method | Test Result | Unit |
---|
Flame Rating | 0.30 mm, ALL | UL 94 | V-0 | |
Oxygen Index | | ISO 527-1,-2(JIS K7161,7162) | 48 | % |
Soldering Resistance | | 内部方法 | 300 | °C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.