Technical Data Sheet
| Physical Properties | Test Condition | Test Method | Test Result | Unit |
|---|
| Modeling Shrinkage | MD | ASTMD955 | 0.65 | % |
| Modeling Shrinkage | | ISO294-4 | 0.30to1.0 | % |
| Moisture Absorption | Saturation,23°C | ASTMD570 | 0.070 | % |
| Moisture Absorption | Saturation,23°C | ISO62 | 0.070 | % |
| Melt Mass-Flow Rate | 200°C/5.0kg | ASTMD1238 | 11 | g/10min |
| Melt Volume flow Rate | 200°C/5.0kg | ISO1133 | 12.0 | cm3/10min |
| Density / Specific Gravity | | ASTMD792 | 1.02 | g/cm³ |
| Density / Specific Gravity | | ISO1183 | 1.02 | g/cm³ |
| Mechanical Properties | Test Condition | Test Method | Test Result | Unit |
|---|
| Nominal Tensile Strain at Break | 23°C | ISO527-2 | 180 | % |
| Flexural Stress | 5.0%Strain | | 31.0 | Mpa |
| Flexural Stress | -- | ISO178 | 31.0 | Mpa |
| Tensile Stress | Yield,23°C | ISO527-2 | 27.0 | Mpa |
| Tensile Strain | Yield,23°C | ISO527-2 | 2.0 | % |
| Tensile Strength | Yield,23°C | ASTMD638 | 25.5 | Mpa |
| Tensile Modulus | | ASTMD638 | 1640 | Mpa |
| Tensile Modulus | | ISO527-2 | 1550 | Mpa |
| Tensile Elongation | Break | ASTMD638 | 220 | % |
| Flexural Modulus | | ASTMD790 | 1330 | Mpa |
| Flexural Modulus | | ISO178 | 1550 | Mpa |
| Flexural Strength | | ASTMD790 | 27.2 | Mpa |
| Thermal Properties | Test Condition | Test Method | Test Result | Unit |
|---|
| Deflection Temperature Under Load? | 0.45MPa,Unannealed | ASTMD648 | 75.6 | °C |
| Deflection Temperature Under Load? | 1.8MPa,Unannealed | ASTMD648 | 60.0 | °C |
| Vicat Softening Temperature | | ASTMD15253 | 87.8 | °C |
| Vicat Softening Temperature | -- | ISO306/A50 | 81.0 | °C |
| Vicat Softening Temperature | -- | ISO306/B50 | 51.0 | °C |
| Linear thermal expansion coefficient | MD | ASTMD696 | 1.3E-04 | cm/cm/°C |
| Linear thermal expansion coefficient | MD | ISO11359-2 | 6.0E-5to9.0E-5 | cm/cm/°C |
| Heat Deflection Temperature | 1.8MPa,Annealed | ISO75-2/A | 58.0 | °C |
| Heat Deflection Temperature | 0.45MPa,Annealed | ISO75-2/B | 75.0 | °C |
| Electrical performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Dissipation Factor? | 100Hz | IEC60250 | 3E-04 | |
| Dissipation Factor? | 1MHz | IEC60250 | 8E-04 | |
| Comparative Tracking Index | | IEC60112 | 600 | V |
| Surface Resistivity | | ASTMD257 | >1.0E+14 | ohms |
| Surface Resistivity | | IEC60093 | 1E+15 | ohms |
| Dielectric Constant | 1.00mm,1MHz | ASTMD150 | 2.50 | |
| Dielectric Constant | 100Hz | IEC60250 | 2.50 | |
| Volume Resistivity | | ASTMD257 | >1.0E+15 | ohms·cm |
| Volume Resistivity | | IEC60093 | >1.0E+15 | ohms·cm |
| Film | Test Condition | Test Method | Test Result | Unit |
|---|
| Elongation - MD | Break | ISO527-3 | 180 | % |
| Impact Properties | Test Condition | Test Method | Test Result | Unit |
|---|
| InstrumentsDartImpact | Totalenergy | ASTMD3763 | 20.1 | J |
| Charpy Unnotched Impact Strength | 23°C | ISO179 | NoBreak | |
| Charpy Notched Impact Strength | 23°C | ISO179 | 3.0 | kJ/m² |
| Notched Izod Impact Strength | 23°C | ASTMD256 | 32 | J/m |
| Notched Izod Impact Strength | -30°C | ISO180/A | 2.0 | kJ/m² |
| Notched Izod Impact Strength | 23°C | ISO180/A | 3.0 | kJ/m² |
| hardness | Test Condition | Test Method | Test Result | Unit |
|---|
| Shore Hardness | Shore D | ASTMD2240 | 75 | |
| Shore Hardness | Shore D | ISO868 | 65 | |
| optical performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Transmittance | 550nm | ASTMD1003 | 91.0 | % |
| Index of Refraction | | ASTMD542 | 1.573 | |
| Haze | | ASTMD1003 | 0.20 | % |
| Refractive index of light | | ISO489 | 1.573 | |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
