Technical Data Sheet
Physical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Modeling Shrinkage | Flow : 3.20 mm | 内部方法 | 0.50 到 0.70 | % |
Modeling Shrinkage | Across Flow 2 | 内部方法 | 0.50 到 0.70 | % |
Moisture Absorption | 24 hr | ASTM D570 | 0.060 | % |
Outdoor Suitability | | UL 746C | f2 | |
Mechanical Properties | Test Condition | Test Method | Test Result | Unit |
---|
Flexural Modulus | 100 mm Span | ASTM D790 | 2640 | Mpa |
Flexural Strength | Yield, 100 mm Span | ASTM D790 | 111 | Mpa |
Tensile Elongation | Yield | ASTM D638 | 9.5 | % |
Tensile Elongation | Break | ASTM D638 | 18 | % |
Tensile Strength | Yield | ASTM D638 | 75.0 | Mpa |
Tensile Strength | Break | ASTM D638 | 55.0 | Mpa |
Thermal Properties | Test Condition | Test Method | Test Result | Unit |
---|
Deflection Temperature Under Load? | 0.45 MPa, Unannealed, 6.40 mm | ASTM D648 | 133 | °C |
Deflection Temperature Under Load? | 1.8 MPa, Unannealed, 6.40 mm | ASTM D648 | 122 | °C |
RTI | | UL 746 | 110 | °C |
RTI Imp | | UL 746 | 105 | °C |
RTI Elec | | UL 746 | 110 | °C |
Vicat Softening Temperature | | ASTM D15255 | 150 | °C |
Electrical performance | Test Condition | Test Method | Test Result | Unit |
---|
Surface Resistivity | | ASTM D257 | > 1.0E+16 | ohms |
Dielectric Constant | 60 Hz | ASTM D150 | 2.57 | |
Dielectric Constant | 50 kHz | ASTM D150 | 2.57 | |
Dielectric Constant | 1 MHz | ASTM D150 | 2.49 | |
Volume Resistivity | | ASTM D257 | 2.0E+16 | ohms·cm |
Dissipation Factor? | 50 Hz | ASTM D150 | 5.2E-3 | |
Dissipation Factor? | 60 Hz | ASTM D150 | 5.2E-3 | |
Dissipation Factor? | 1 MHz | ASTM D150 | 2.6E-3 | |
Dielectric Strength | 3.20 mm, in Oil | ASTM D149 | 19 | KV/mm |
High Voltage Arc Tracking Rate | | UL 746 | PLC 4 | |
Arc Resistance | | ASTM D495 | PLC 6 | |
Comparative Tracking Index | | UL 746 | PLC 2 | |
High Amp Arc Ignition | | UL 746 | PLC 0 | |
Hot-wire Ignition | | UL 746 | PLC 0 | |
Injection | Test Condition | Test Method | Test Result | Unit |
---|
Drying Time | | | 3.0 到 4.0 | hr |
Suggested Shot Size | | | 30 到 70 | % |
Rear Temperature | | | 245 到 295 | °C |
Middle Temperature | | | 255 到 300 | °C |
Front Temperature | | | 265 到 305 | °C |
Nozzle Temperature | | | 275 到 305 | °C |
Back Pressure | | | 0.300 到 0.700 | Mpa |
Screw Speed | | | 20 到 100 | rpm |
Vent Depth | | | 0.038 到 0.051 | mm |
Drying Temperature | | | 105 到 110 | °C |
Suggested Max Moisture | | | 0.020 | % |
Processing (Melt) Temp | | | 275 到 305 | °C |
Mold Temperature | | | 70 到 100 | °C |
Impact Properties | Test Condition | Test Method | Test Result | Unit |
---|
Unnotched Izod Impact Strength | 23°C | ASTM D4812 | 1100 | J/m |
Instrumented Dart Impact | 23°C, Energy at Peak | ASTM D3763 | 42.0 | J |
Flammability | Test Condition | Test Method | Test Result | Unit |
---|
Flame Rating | 0.76 mm | UL 94 | V-0 | |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.