Technical Data Sheet
Compare
| physical property | Test Condition | Test Method | Test Result | Unit |
|---|
| Shrinkage rate | MD1 | 内部方法 | 0.50到0.70 | % |
| Water absorption rate | Saturation,23°C | ISO62 | 0.35 | % |
| Water absorption rate | Equilibrium,23°C,50%RH | ISO62 | 0.15 | % |
| Melt volume flow rate | 300°C/1.2kg | ISO1133 | 18.0 | cm3/10min |
| Outdoor applicability | | UL746C | f1 | |
| Mechanical performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Bending stress 3 | | ISO178 | 90.0 | Mpa |
| Tensile stress | Yield | ISO527-2/50 | 62.0 | Mpa |
| Tensile stress | Break | ISO527-2/50 | 69.0 | Mpa |
| Tensile strain | Yield | ISO527-2/50 | 6.0 | % |
| Tensile strain | Break | ISO527-2/50 | 100 | % |
| Tensile modulus | | ISO527-2/1 | 2350 | Mpa |
| Taber abraser | 1000Cycles,1000g,CS-17Wheel | 内部方法 | 10.0 | mg |
| Bending modulus 2 | | ISO178 | 2300 | Mpa |
| Thermal performance | Test Condition | Test Method | Test Result | Unit |
|---|
| 0.45MPa, unannealed, 100mm span | | ISO75-2/Be | 133 | °C |
| 1.8MPa, unannealed, 100mm span | | ISO75-2/Ae | 122 | °C |
| Linear coefficient of thermal expansion | MD：23to80°C | ISO11359-2 | 7E-05 | cm/cm/°C |
| RTIElec | | UL746 | 130 | °C |
| Evolution Calendar intelligent importer | | UL746 | 125 | °C |
| thermal conductivity | | ISO8302 | 0.20 | W/m/K |
| RTI | | UL746 | 125 | °C |
| BallPressure Test | 125°C | IEC60695-10-2 | Pass | |
| -- | | ISO306/B50 | 140 | °C |
| -- | | ISO306/B120 | 141 | °C |
| Electrical performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Dissipation factor | 50Hz | IEC60250 | 1E-03 | |
| Dissipation factor | 60Hz | IEC60250 | 1E-03 | |
| Dissipation factor | 1MHz | IEC60250 | 0.010 | |
| Relative permittivity | 50Hz | IEC60250 | 2.70 | |
| Relative permittivity | 60Hz | IEC60250 | 2.70 | |
| Relative permittivity | 1MHz | IEC60250 | 2.70 | |
| Leakage Trace Index | | IEC60112 | 250 | V |
| Surface resistivity | | IEC60093 | >1.0E+15 | ohms |
| Volume resistivity | | IEC60093 | >1.0E+15 | ohms·cm |
| Dielectric strength | 3.20mm,in Oil | IEC60243-1 | 17 | KV/mm |
| Impact performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Simply supported beam without notch impact strength 5 | 23°C | ISO179/1eU | 无断裂 | |
| Simply supported beam without notch impact strength 5 | -30°C | ISO179/1eU | 无断裂 | |
| Suspended wall beam notch impact strength 6 | -30°C | ISO180/1A | 15 | kJ/m² |
| Suspended wall beam notch impact strength 6 | 23°C | ISO180/1A | 65 | kJ/m² |
| Unscented Izod Impact Strength 7 | -30°C | ISO180/1U | 无断裂 | |
| Unscented Izod Impact Strength 7 | 23°C | ISO180/1U | 无断裂 | |
| Impact strength of simply supported beam gap 4 | -30°C | ISO179/1eA | 12 | kJ/m² |
| Impact strength of simply supported beam gap 4 | 23°C | ISO179/1eA | 65 | kJ/m² |
| hardness | Test Condition | Test Method | Test Result | Unit |
|---|
| Ball pressure hardness | H358/30 | ISO2039-1 | 95.0 | Mpa |
| optical performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Haze | 2540µm | ASTMD1003 | <0.50 | % |
| Refractive index | | ISO489 | 1.586 | |
| 2540 µ M | | ASTMD1003 | >90.0 | % |
| 2540µm,420nm | | 内部方法 | >88.0 | % |
| 5000 µ M | | 内部方法 | >89.0 | % |
| flammability | Test Condition | Test Method | Test Result | Unit |
|---|
| UL flame retardant rating | 0.800mm,TestingbySABIC | UL94 | V-2 | |
| Burning wire flammability index | 1.00mm | IEC60695-2-12 | 850 | °C |
| Extreme Oxygen Index | | ISO4589-2 | 25 | % |
| Hot filament ignition temperature | 1.00mm | IEC60695-2-13 | >875 | °C |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
