Technical Data Sheet
Compare
| Physical properties | Test Condition | Test Method | Test Result | Unit |
|---|
| density | | ASTM D792/ISO 1183 | 1.29 | |
| Water absorption rate 23 ℃/24h | | ASTM D570/ISO 62 | 1.3 | % |
| physical property | Test Condition | Test Method | Test Result | Unit |
|---|
| Shrinkage rate | TD:3.00mm3 | % | 0.60到0.90 | -- |
| Shrinkage rate | MD:3.00mm4 | % | 0.30到0.50 | -- |
| Water absorption rate | 23°C,24hr | % | 1.3 | -- |
| Water absorption rate | Saturation,23°C | % | 7.8 | -- |
| Taber wear amount | (1000g,CS-17)23 ℃ | ASTM D-1044 | 12 | mg/1000次 |
| Enhanced content | | | 20 | wt% |
| Mechanical performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Flexural modulus | 23℃ | ASTM D-790 | 60000 | kg/cm |
| Izod Heng Strike | 23℃ V-Notched1/2 | ASTM D-256 | 6 | kg·cm/cm |
| Flexural strength | -40℃ | ASTM D-790 | 2400 | kg/cm |
| Rockwell hardness | R-标度 23℃ | ASTM D-785 | 120 | |
| Elongation at break | 23℃ | ASTM D-638 | 5 | % |
| Flexural modulus | -40℃ | ASTM D-790 | 78000 | kg/cm |
| Rockwell hardness | M-标度 23℃ | ASTM D-785 | 92 | |
| Tensile and flexural strength | 23℃ | ASTM D-638 | 1200 | kg/cm |
| Flexural modulus | 80℃ | ASTM D-790 | 29000 | kg/cm |
| Flexural strength | 23℃ | ASTM D-790 | 1800 | kg/cm |
| Flexural strength | 80℃ | ASTM D-790 | 1000 | kg/cm |
| Tensile strain | Break,23°C | % | 3.0 | |
| Tensile strain | Break,80°C | % | 5.0 | 5.5 |
| Bending modulus | -40°C | MPa | 8700 | 7300 |
| Bending modulus | 23°C | MPa | 6800 | 3500 |
| Bending modulus | 80°C | MPa | 3200 | 2600 |
| Bending stress | -40°C | MPa | 275 | -- |
| Bending stress | 23°C | MPa | 205 | -- |
| Bending stress | 80°C | MPa | 115 | -- |
| Compressive stress | -40°C | MPa | 240 | -- |
| Rockwell hardness | | ASTM D785 | R120,M92 | |
| Tensile stress | 23°C | MPa | 120 | -- |
| Tensile strain | Break,-40°C | % | 2.5 | 3.0 |
| Compressive stress | 23°C | MPa | 155 | 80.0 |
| Compressive stress | 80°C | MPa | 90.0 | -- |
| shear strength | 23°C | MPa | 115 | 65.0 |
| Taber abraser | 1000Cycles | mg | 0.300 | -- |
| Friction coefficient vs. Metal5 | | | 0.15 | -- |
| Thermal performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Hot deformation temperature | 0.45MPa,Unannealed | °C | 215 | -- |
| Melting temperature | | °C | 225 | -- |
| melting point | | 差示扫描测热计DSC | 225 | °C |
| heat deflection temperature | 18.6kg/cm | ASTM D-648 | 185 | °C |
| specific heat | | | 0.36 | Cal/g·℃ |
| Linear coefficient of thermal expansion | | ASTM D-696 | 3 | |
| heat deflection temperature | 4.6kg/cm | ASTM D-648 | 215 | °C |
| Linear coefficient of thermal expansion | MD | cm/cm/°C | 3E-05 | -- |
| specific heat | | J/kg/°C | 1600 | -- |
| thermal conductivity | | W/m/K | 0.33 | -- |
| melting point | | | 225 | ℃（℉） |
| Electrical performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Volume resistivity | | ASTM D257/IEC 60093 | 10^13 | Ω.cm |
| Volume resistivity | | ohms·cm | 1E+15 | 1E+12 |
| Dielectric strength | | kV/mm | 20 | -- |
| Dielectric constant 6 | 23°C,50Hz | | 4.60 | -- |
| Dielectric constant 6 | 23°C,1kHz | | 4.40 | -- |
| Dielectric constant 6 | 23°C,1MHz | | 3.80 | -- |
| Dissipation factor 6 | 23°C,50Hz | | 0.040 | -- |
| Dissipation factor 6 | 23°C,1kHz | | 0.040 | -- |
| Dielectric strength | 1/8" 短时间 | ASTM D-149 | 20 | KV/mm |
| Volume resistivity | | ASTM D-257 | 10 | Ω·cm |
| Dissipation factor 6 | 23°C,1MHz | | 0.030 | -- |
| Arc resistance 7 | | sec | 120 | -- |
| Impact performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Impact strength of simply supported beam without notch | -40°C | kJ/m² | 25 | |
| Impact strength of simply supported beam without notch | 23°C | kJ/m² | 55 | |
| hardness | Test Condition | Test Method | Test Result | Unit |
|---|
| Rockwell hardness | M-Sale,23°C | | 92 | -- |
| Rockwell hardness | R-Sale,80°C | | 12 | -- |
| Rockwell hardness | R-Sale,23°C | | 120 | -- |
| flammability | Test Condition | Test Method | Test Result | Unit |
|---|
| UL flame retardant rating | 1.6mm | | HB | -- |
| Basic performance | Test Condition | Test Method | Test Result | Unit |
|---|
| Water absorption rate | 24hr 23℃ | ASTM D-570 | 1.3 | % |
IMPORTANT NOTES: Plas.com collected the data in the data sheet from the material manufacturers. Plas.com makes the best effort to improve the accuracy of the data, but has no responsibility for the data. We strongly recommend verifying the validity of the data with the material manufacturers before making a final decision.
